Cardin Elettronica ZVL120.00 Manual De Instrucciones página 14

Cancelling the entire memory content
Press "P2" three times and hold down after pressing the third time. During the cancellation procedure
(3-4 seconds) LED "L3" remains lit.
After cancellation the LED will flash 3 times; at this point release the button.
Memorising ulterior channels via radio
• Memorisation can be activated via radio (without opening the receiver container) if jumper "J5" has
been inserted. Activation will be indicated by the buzzer sounding.
1) Using a transmitter, in which at least one channel button "A,B,C or D" has
already been memorised in the receiver, press the button "MR" as shown
in the figure.
Note: all the receivers within range when the channel button is pressed
(and which have at least one of the transmitter channel buttons memorised)
will activate their signal buzzer "B1" (fig. 1).
2) To select the receiver in which to memorise the new code activate one of the channels on the same
transmitter. The receivers which do not contain that channel code will sound a five-second long
"beep" and will then deactivate. The receivers which contain the channel code will sound a one-
second long "beep" and will enter the "programming via radio" mode.
3) Press the channel buttons on the pre-selected transmitter that you wish to memorise; the receiver
will sound 2 "beeps" of half a second each after which the receiver will be ready to receive another
code.
4) To leave the programming mode wait for 3 seconds without memorising any codes. The receiver
will sound a five-second long "beep" and will then exit the programming mode.
When the memory is entirely occupied the buzzer will sound 10 rapid "beeps" and will automatically
leave the "programming via radio" mode. The same signal is given each time you try to enter "pro-
gramming via radio" when the memory is full.
MANAGING THE DISPLAY KEYBOARD LCD AND LED (fig. 2)
It is possible to use the MDK RT/MDK RTL to activate single or groups of radio programmers: The
command will have to be memorised in the radio programmer.
Note: the "general" command will activate all devices that have at least one command memorised.
Memorising a single or group command)
1) Press and hold down button "P2" on the radio programmer (LED "L3" will flash slowly).
2) - for a single command: select the unit using buttons 4 and 6;
- for a group command: press button 5 and then select the group using buttons 4 and 6.
3) Press button 1 to send the command: LED "L3" will flash 3 times to confirm memorisation; if the
LED continues to flash slowly the code is already stored in memory. To insert another code repeat
points 1 to 3 after first releasing button "P2". Up to 4 keyboards can be memorised.
Cancelling a single or group command
1) Press button "P2" twice and hold down (LED "L3" will flash at brief intervals).
2) - for a single command: select the unit using buttons 4 and 6;
- for a group command: press button 5 and then select the group using buttons 4 and 6.
3) Press button 1 to send the command: LED "L3" will flash 3 times to confirm cancellation. To insert
another code repeat points 1 to 3 after first releasing button "P2".
Cancelling everything "single command/group/general"
1) Press button "P2" twice and hold down (LED "L3" will flash at brief intervals)
2) Press button 5.
3) Press button 1 to send the "general" command: LED "L3 will flash 3 times to confirm the cancella-
tion of the keyboard.
For more information regarding the LCD/LED keyboards see the instructions supplied with the product.
Drawing number :
Product Code :
Draft : P.J.Heath
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/40183
14
Description : MEMORIZZAZIONE CODICE TX-RX
DM0531
RCQ449100
Date : 13-04-2001