Hama DJ-JOY 2.0 Manual Del Usuario página 3

Audiomixer DJ-JOY 2.0
L
Rear view
Top view
PHONO2/LINE2 A B
PHONO1/LINE1 PFL
A B
PHONE
LEVEL
MICRO
A B
Front view
2-channel mixer console for home music systems,
e.g. keyboards, CD-player, record player or other
audio sources and hifi amplifier.
Mixer console features:
• 2 stereo channels each for Phono/Line,
switchable (4 inputs)
• Cross-fader to cross-fade the two input channels
A and B
• Variable stereo headphones output
Connection: 6.3 mm jack-plug socket
• Two-colour stereo LED display (switch-over
between inputs)
• Variable microphone input
Connection: 6.3 mm jack-plug socket
• Supplied with mounting bracket (detachable) for
permanent or table-top installation
• With earthing screw for record player
• Dimensions: 23.3 x 13 x 5.5 cm (incl. mounting
bracket)
• Mains adapter included
Operating Instructions
1. The mains switch (POWER) must be in the OFF
position when the individual units are connected
(= button not depressed).
2. Connect the power supply cable of the mains
adapter to the mixer console.
3. Plug the mains adapter directly into the 220 V
mains.
4. To avoid voltage peaks it is advisable to set all
slide controls on the mixer console, as well as the
volume control of the amplifier, at O-position
(minimal).
5. • Connect all playback units with the respective
cinch sockets at the back of the mixer console.
• The "AMP" cinch sockets are used to connect
the hifi amplifier.
• A microphone input is in the back panel mixer
console.
• A headphones input is in the back panel of the
• mixer console.
6. • The entire system can be set into operation
after all the individual units have been
connected.
• Switch on the mixer console with its POWER
switch (depress).
• Select the required programme source by
positioning the input selector switch „PHONO 1/
LINE 1", „PHONO 2/LINE 2" accordingly. The
position of the individual slide controls and the
volume control of the amplifier determine the
signal strength.
• The signal strength of the headphones output is
variable with the „Phone Level" rotary control.
The input signal can be monitored with head-
phones (pre-hear) for specific playback of a
certain piece of music. The "PFL" toggle switch
can be set between "A" and "B" to adjust the
required input.
• The signal strength of the microphone is
adjusted with the "MICRO" rotary control.
Safety Instructions:
• Only use in closed rooms!
• Always transport the audio mixer console in the
original cardboard box or a case that has been
cushioned accordingly.
• Only clean with a moist cloth or with correspon-
ding cleaning agents.
• The mixer must only be opened and repaired by a
qualified technician.
Technical data:
5 inputs (1x Microphone, 2x Phono, 2x Line)
2 x 5 LED display rows
1 cross-fader
2 channel faders
Inputs: Microphone: 1 mV/1 kOhm
Phono: 3 mV/50 kOhm
Line 1 and 2: 150 mV/100 kOhm
Outputs: AMP: 1.5 V/600 Ohm
Frequency response: 2-47,000 Hz +1 dB
Power supply: 220 V/50 Hz (AC)
Dimensions (w/h/d): 233 x 55 x 130 mm
Weight: 765 g
Mains adapter included: 12 V/300 mA (AC)
Controls and connecting elements:
1 Microphone socket
2 PHONO 1/2, LINE 1/2 input selector switch
3 LED meter
4 Mains switch
5 Headphones socket
6 Headphones volume control
7 Selector switch for pre-hear monitoring
8 Cross-fader
9 Slide control for A/B source
10 Socket for plug-in mains adapter
11 Cinch sockets to connect the amplifier
12 Line/Phono inputs
13 MICRO control