Sony SRS-T033 Manual De Instrucciones

Active Speaker System
Operating Instructions
Manual de instrucciones
SRS-T033
© 2004 Sony Corporation
A
1
v
B
1
(rear)
C
D
POWER indicator
3-265-568-11(1)
Printed in China
2
2
Two R03 (size AAA) batteries
CD player
To headphones jack
(stereo mini jack)
POWER
English
Before operating the unit, please read this manual
thoroughly and retain it for future reference.
Precautions
On safety
• Operate the system only on 3 V DC (two size AAA
(R03) batteries).
• If the system is not to be used for a long period of
time, remove the batteries to avoid damage caused
by battery leakage and corrosion.
On operation
• Do not open the cabinet. Refer servicing to qualified
personnel only.
• Should any solid object or liquid fall into the system,
have the system checked by qualified personnel
before operating it any further.
If the TV picture or monitor display is
magnetically distorted
Although this system is magnetically shielded, there
may be cases that the picture on some TV sets/personal
computer sets may become magnetically distorted. In
such a case, turn off the power of the TV set/personal
computer set once, and after 15 to 30 minutes turn it on
again. For the personal computer set, take the
appropriate measures such as data storage before
turning it off.
When there seems to be no improvement, locate the
system further away from the TV set/personal
computer set. Furthermore, be sure not to place objects
in which magnets are attached or used near the TV set/
personal computer set, such as audio racks, TV stands,
toys etc. These may cause magnetic distortion to the
picture due to their interaction with the system.
On placement
• Do not set the speakers in an inclined position.
• Do not leave the system in a location near heat
sources, or in a place subject to direct sunlight,
excessive dust, moisture, rain or mechanical shock.
On cleaning
Do not use alcohol, benzine, or thinner to clean the
cabinet.
If you have any questions or problems concerning your
speaker system, please consult your nearest Sony
dealer.
Preparation
Pulling out the input cord
(See fig. A)
Pull out the input cord before use.
1
Slide the stand to open it.
2
Tilt the speaker to pull out the input
cord.
Note
The input cord is stored in the rear of the speaker. Pull
out the input cord, before you open the compartment
lid.
Battery installation
(See fig. B)
Battery replacement
When the batteries are weak, the POWER indicator will
start flickering and become faint, or the playback sound
will become distorted or unstable. In such a case,
replace all the batteries with new ones.
Battery life (5 mW + 5 mW output)
Battery type Usage time
Sony alkaline battery LR03 (SG) Approx. 16 hours*
Sony manganese battery R03 Approx. 8 hours*
* Usage time stated above may vary according to the
temperature or conditions of use.
Hooking up the speakers
(See fig. C)
When the system is connected to the monaural jack
of a radio, etc., the sound may not come through the
right speaker. In such a case, use the optional* plug
adaptor PC-236MS.
To connect to a stereo phone-type
headphones jack
Use the optional* PC-234S plug adaptor or RK-G138
connecting cord.
* The above optional accessories are not provided in some
areas.
Listening to the sound
(see fig. D)
Before connecting the speakers to the headphone
output, reduce the volume of the connected
component.
1
Set the POWER switch to ON.
The POWER indicator lights up.
2
Play back the connected component.
Adjust the volume of the connected component.
After listening, set the POWER switch to OFF/
DIRECT.
The POWER indicator goes off.
Note
Turn off the Parametric equalizer function as it may
cause audible distortion.
To operate this unit without the built-in
amplifier
Set the POWER switch to OFF/DIRECT.
Troubleshooting
Should you have a problem with your speaker system,
check the following list and take the suggested
measures. If the problem persists, consult your nearest
Sony dealer.
There is no sound from the speaker
system.
• Make sure all the connections have been correctly
made.
• Make sure the volume on the connected component
has been turned up properly.
• Replace all the batteries with new ones.
The sound is distorted.
• Turn down the volume level on the connected
component. Or, if the connected component has a
bass boost function, set it to off.
• Replace all the batteries with new ones.
There is hum or noise in the speaker
output.
• Make sure all the connections have been correctly
made.
• Make sure none of the audio components are
positioned too close to the TV set.
The sound has suddenly stopped.
Make sure all the connections have been correctly
made.
Specifications
Speaker section
Enclosure type Full range, Bass reflex,
magnetically shielded
Speaker system 34 mm (diameter)
3.2 Ω
Impedance
Rated input power 0.2 W
Maximum input power 0.6 W
Amplifier section
Rated output 0.18 W + 0.18 W
(10% T.H.D., 1 kHz, 3.2 Ω)
Bass boost MEGA BASS
Input Input cord a stereo-mini plug
(25 cm) × 1
Input impedance 4.7 kΩ (at 1 kHz)
General
Power Two R03 (size AAA) batteries
approx. 174 × 46 × 32 mm
Dimensions (w/h/d)
× 1 × 1
(6 7 ⁄ 13 ⁄ 5 ⁄ inch)
8 16 16
Mass Approx. 145 g (5.2 oz.) not incl.
batteries
Design and specifications are subject to change without
notice.