Using The Appliance; Cleaning And Maintenance - Moulinex COSMO MO6527 Manual De Instrucciones

901866_not_cosmo.qxd:901866

USING THE APPLIANCE

1. ASSEMBLING THE ELEMENTS OF THE APPLIANCE
Note!
Always stop and unplug your vacuum cleaner before changing accessories.
• Push the flexible hose (19) in the opening (8) until your hear a clicking sound - fig. 1.
• To remove it, press the clips on the tube (19) and pull - fig. 2.
• Assemble the telescopic tube* (20). Adjust it to the desired length - fig. 3.
• Fit the appropriate accessory to the end of the tube:
- For rugs and wall-to-wall carpeting: use the head (22) with brushes lifted - fig. 4a.
- For parquets and smooth flooring: use the nozzle (22) with the brush extended - fig. 4b. or use the
parquet nozzle* (23).
- For corners and other areas that are difficult to reach, use the slot attachment convertible into a
brush* (25) in the flat attachment position.
- For furniture, use the slot attachment convertible into a brush* (25) or the furniture nozzle (24).
2. PLUGGING IN THE ELECTRICAL POWER CORD AND USING THE VACUUM CLEANER
• Completely unwind the power cord, plug in your vacuum cleaner and push the on/off pedal (2) - fig. 5.
• Set the suction power:
- using the electronic power regulator (3): turn the switch on the electronic regulator to set the suction
power: towards max position for floors and min position for furniture and fragile fabrics - fig. 6a.
- with the mechanical power regulator on the grip: Open the manual suction regulator to reduce the
suction power manually – for fragile surfaces, for example - fig. 6b.
3. STORING AND TRANSPORTING THE APPLIANCE
• After use, stop your appliance by pressing on the on/off pedal (2) and unplug it - fig. 7. Replace the
cable by pressing the automatic cable rewind pedal (4) - fig. 8.
• In the horizontal position, hook the floor nozzle (22) onto its storage position at the rear of the
appliance (1a) - fig. 9a.
• Upright, place the attachment (22) in its housing under the appliance (1b) - fig. 9b.
• Carry your vacuum cleaner easily thanks to its carry handle (6).

CLEANING AND MAINTENANCE

Important!
Always stop and unplug your vacuum cleaner before maintenance or cleaning.
1. EMPTY AND CLEAN THE DUST BOX
1.1. EMPTY THE DUST BOX
• Empty the dust box (11) after each use.
• Remove the flexible tube (19) from the suction opening (8) - fig. 2.
• Open the lid (7) of your vacuum cleaner.
• Remove the dust box (11) from its housing (9) - fig. 10.
• Press the box opening zone (14) to open it - fig. 11.
• Remove the lid - fig. 12, empty the box over a dustbin - fig. 13a.
• Make sure no dust is left in the box, then clean the edges of the box - fig. 13b.
• Close the dust box and replace it in its housing (9).
1.2. CLEAN THE DUST BOX
• You can also run the dust box under soapy water only after having previously removed the HEPA
filter capsule (18), or the black foam filter (18a) and the HEPA filter (18b).
• After having emptied the dust box out over a dustbin - fig. 13a, unclip the HEPA filter capsule (18), by
simultaneously pressing the opening clips (15) located on either end of the box - Figure 14a.
• Remove the HEPA filter capsule (18) - fig. 14b.
• Run the dust box under soapy water and leave it to dry for 12 hours - fig. 14c.
• Once the box is completely dry, replace the HEPA filter capsule (18): black foam filter (1880) and HEPA
filter (18b) under the box and replace the dust box (11) in its housing (9) - fig 15.
*Depending on model: it means special equipment for some models or optional accessories.
27/05/08 16:56 Page 9
9
GB