Charging The Battery - Felisatti RH26/36CVR Instrucciones De Servicio

Uncertainty(K)
2. The operator to wear hearing protection
3.Vibration emission
Vibration total values(triaxial vector sum) determined
according to EN 60745
C h i s e l l i n g Vibration emission
Hammer mode value(ah)
Uncertainty(K)
H a m m e r Vibration
drilling mode value(ah)
Uncertainty(K)
4.The following information
The declared vibration total value has been measured in
accordance with a standard test method given in EN 60745
and may be used for comparing one tool with another.
The declared vibration total value may also be used in a
preliminary assessment of exposure.
5.A warning
The vibration emission during actual use of the power tool
can differ from the declared total value depending on the
ways in which the tool is used.
Identify additional safety measures to protect the operator
that are based on an estimation of exposure in the actual
conditions of use (taking account of all parts of the operating
cycle such as the times when the tool is switched off and
when it is running idle in addition to the trigger time).
APPLICATIONS
• Boring into Concrete
• Breaking up concrete
• Making hole for anchor bolt
• Consolidation, making groove, removal, etc.
[Example of Uses]
Cooling and heating work, piping and wiring work, sanitary
arrangements work, installation of mechanism, water supply
and drainage work, interior work, steel structure installation,
other civil engineering equipment repair work.
OPERATING INSTRUCTIONS

CHARGING THE BATTERY

1. Plug the charger into the power outlet. Within 1 second,
the charging indicator flickers twice each in the order of green
red yellow and go into charge standby mode.
2. Now, inserting the battery into the charger will immediately
start charging.
3. If work time of the battery is too short even after fully
charged, the batter has to be replaced immediately as its life
is ended.
The batteries accompanying with the product as
purchasing or those not have been
used for a long time can be used again after recharging.
ATTENTION: Be careful not to make the terminals of the
battery short.
Short circuit of battery may cause fire or explosion and
serious injuries may be resulted in.
3 dB
7.5 m/s
1.5 m/s
emission 11 m/s
1.5 m/s
CHARGING STATUS INDICATION (Fig.1.
ATTENTION: Be sure to use only specified battery and
charger.
If any other battery or charger than specified is used, fire,
explosion, charging failure or overheat may be caused.
1. Charging Indicator
Charging standby
Blinking green
Charging in progress
Red On
Charging completed
Green On
Overheat standby (Battery too hot)
Blinking Red
Charging not available
Blinking Yellow
ATTENTION: Be sure to unplug the charger power cord
after completing charging.
2. If charging with hot battery is tried immediately after being
just used or charged, the indicator blinks in red (overheat
standby).
Cooling fan built in the charger automatically starts running
to cool the hot battery down to normal temperature and, after
cooling, indicator is changed to red and normal charging
starts.
3. This charger detects electricity of the battery to always
allow making full charging.
ATTACHING AND REMOVING BATTERY (Fig.2.
1. Attaching
• Set the forward/backward level in neutral position
(locked).
• Place the charged battery from under the handle of
product and push it to its position until you hear two clicks.
2. Removing
• Press Right/Left button located at the side of battery.
• Pull the battery backward to remove it.
ATTENTION: Be sure to set the Forward/Backward lever
in neutral position when changing battery or tool, or
during transportation or storage.
BATTERY LEVEL INDICATOR (Fig.3.
For checking battery level, ON is displayed.
1 = 66~100%(LED 3 bar on)
2 = 33~66% (LED 2 bar on)
3 = 5~33% (LED 1 bar on)
4 = Less than 5% (LED 1 bar blinks)
LIGHTING FEATURE (Fig.4.
1. It is convenient to use lighting feature when working in a
dark place.
2. Pressing the light button with arrow mark to turn light on
and pressing again off.
Light automatically turns off 1 minute after turning on.
ASSEMBLING SIDE HANDLE
AND ADJUSTING STOPPER
ATTENTION: In case an operation of drilling into concrete
and stone is carried out, be sure to attach the side handle
5