Boiling Water; Cleaning And Maintenance; Protecting The Environment - Black and Decker DC55 T1 Manual De Instrucciones

ENGLISH
Extension cables & class 1 product
If an extension lead is required a 3 core cable must be used
as your appliance is earthed and of class 1 construction.
Up to 30m (100ft) can be used without loss of power.
Power plugs must match the outlet. never modify the
plug in anyway. Do not use any adapter plugs with
earthed (Class 1) appliances. Unmodified plugs and
matching outlets will reduce the risk of electric shock.
Features
1. Lid
2. Lid handle
3. Handle
4. On/off indicator light
5. Water level window
6. Spout
Before first use
Remove all packaging from the appliance,
Clean the appliance before first use.
Remove the lid (1) by turning it anti clockwise and lifting
it clear of the unit.
Fill the kettle with cold water to the maximum fill mark.
Do not overfill as described below.
Replace the lid (1) by aligning the open icon on the lid
(1) and pip on the kettle body then turn clockwise to
lock. The pip on the body and the close icon
be aligned.
Boil the water as described below.
Discard the boiled water and repeat the procedure.
Use
Warning! Always place the appliance on a flat, clean and
non-slip surface before operating it.
Warning! Always check the water level while using the
appliance. Never use the appliance without sufficient water.
Warning! The outer surfaces of the kettle may become hot
in use.
Warning! Do not remove the lid while the water is boiling.
Warning! Steam may escape from the spout.
Warning! Allow the Appliance to cool before re-filling

Boiling water

Unplug the kettle and take it to a water outlet
Remove the lid (1) as described above.
Fill the kettle with cold water to the desired level. Do not
overfill.
To prevent dry boiling fill to at least 240ml (two cups)
Do not fill the kettle beyond the maximum fill mark. If the
kettle is overfilled, boiling water may be ejected from the
spout (6).
4
Replace the lid (1) and ensure it is in the locked position
with the closed icon
Insert the plug into a power socket. The unit will switch
on immediately and the on/off indicator light (4) will light.
After a short period the water will begin to boil.
The unit will continue to boil until the plug is removed
from the power socket. Do not open the lid (1) when the
water is boiling.
Pouring boiled water
Make sure the unit is disconnected from the power
socket.
To avoid scalding, tilt the kettle slowly to pour the boiled
water.

Cleaning and maintenance

Warning! Before cleaning and maintenance, switch the
appliance off, remove the plug from the socket and allow the
appliance to cool.
Warning! Do not immerse the appliance or the cord set or
the plug in water or any other liquid.
Wipe the exterior with a damp cloth.
Do not use scouring pads.
If necessary, use a mild detergent to remove spots. Do
not use any abrasive or solvent based cleaner.
Descaling the appliance
should
If the appliance is used in an area with hard water, it is
advised to descale the appliance from time to time.
Half fill the kettle with cold tap water.
Add 30 ml of white vinegar.
Boil the mixture and allow it to stand for 30 seconds.
Repeat this procedure 2 or 3 times.
Thoroughly rinse the kettle.

Protecting the environment

Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again. Re-
use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
in line with the pip on the body.