Automation Direct PSP Serie Instrucciones De Instalación

Input
Part Number
Voltage Range
PSP24-024S
PSP24-024C
PSP12-060S
Universal Input
PSP12-060C
85VAC – 264VAC
PSP24-060S
50 / 60Hz
PSP24-060C
85 – 375VDC**
PSP12-120S
PSP12-120C
PSP24-120S
PSP24-120C
* Adjustable by potentiometer with a screwdriver.
** Below 93VAC or 130VDC use 83% max rated power (80% for PSPxx-024x)
The PSP series power supplies meet EN 61000-3-2 (PFHC: Power Factor Harmonic Current) Class A.
Input current: @ Vin=115VAC
Ø PSP24-024x
0.7A max
Ø PSPxx-060x
1.4A max
Ø PSPxx-120x
2.4A max
Operating temperature range:
Natural Air Convection Cooling
Output Power Derating:
Storage temperature range:
Parallel Operation:
Connections:
Case material:
Output Signals:
Output Voltage nominal
Output Voltage threshold (DC is OK)
DC OK Signal Voltage
DC OK Signal Current
Load characteristic
To Install:
1. Read and follow Safety and Installation Instructions on the back of this page.
2. Hook top of power supply's DIN rail clip on DIN rail.
3. Push down tab on top of power supply to open DIN rail clip.
4. Rotate power supply into DIN rail and release tab.
5. Verify the DIN rail clip is securely fastened on DIN rail.
6. Connect wires as indicated on power supply.
http:// www.automationdirect.com
INSTALLATION INSTRUCTIONS
PSP Series Industrial Power Supply
Output
Power max.
24 Watt 24.0VDC / 1.0A
12.0VDC / 4.0A
60 Watt
24.0VDC / 2.5A
12.0VDC / 8.0A
120 Watt
24.0VDC / 5.0A
@ Vin=230VAC
0.4A max.
0.8A max
1.2A max
-10°C – +70°C max
+14°F – +158°F max
above +50°C (122°F) è 1.7
above +40°C (104°F) è 1.1
above +30°C (86°F) è 1.3
Ambient air temperature measured 0.39in (10mm) below power supply.
-25°C – +85°C max (-13°F – +185°F max)
Up to 5 power supplies possible
Ø Screw type plug-in connector (option S) è 20 – 13 AWG (0.5 – 2.5mm
Recommended tightening torque 0.5 to 0.7Nm (4.5lb.in. to 6.2lb.in.)
Ø Cage-clamp connector (option C) è 20 – 13 AWG (0.5 – 2.5mm
Ø Use all terminals.
Ø Use a screwdriver with 0.1378 (3.5 mm) blade width (AutomationDirect part DN-SS3).
Plastic FR2010-110C (UL 94 V-0 rated)
12.0 / 15.0 VDC
9.0 ... 11.0 V
11.0 V ±1.0V
Resistive or Inductive
* Output Voltage
Output
Adjustment Range
24.0 – 28.0VDC
12.0 – 15.0VDC
24.0 – 28.0VDC
12.0 – 15.0VDC
24.0 – 28.0VDC
Power Consumption @ Vin=115VAC @ Vin=230VAC
Ø PSP24-024x
Ø PSPxx-060x
Ø PSPxx-120x
Free Space Requirements: Top and Bottom: 3.15 in (80 mm)
Both Sides: 1.97in (50mm)
%
/ at an input voltage of 187...264VAC or 265...375VDC
°C
%
/ at an input voltage of 93...132VAC or 130...187VDC
°C
%
/ at an input voltage of 85...130VDC
°C
60 mA
recommended Circuit
breaker (Characteristic C)
5A
10A
28 Watt typ. 27 Watt typ.
71 Watt typ. 68 Watt typ.
137 Watt typ. 133 Watt typ.
2
) wire
2
) wire
24.0 VDC
18.0 ... 22.0 V
22.0 V ±2.0V
30 mA
Resistive or Inductive
Rev: 09/03