Publicidad
Idiomas disponibles
Idiomas disponibles
H-2540, H-2541
DOUBLE-SIDED GRID
BIKE RACK
TOOL NEEDED
9/16" Wrench
Leg x 2
1.
Insert bolt upward through last hole in leg and pole.
Fasten loosely with locknut. Repeat by attaching
other leg to pole. (See Inset A)
2. Insert bolt through hole at the top of the leg and
end of grid. (See Inset B)
NOTE: Grid can only be positioned one way
for mounting. The holes on top are drilled
diagonally through the tube at a slight
downward angle.
3. Fasten loosely with locknut. Repeat by
attaching other leg to grid.
4. Align bottom holes of grid with middle hole of legs.
Insert bolt upward and fasten loosely with locknut.
Repeat by attaching other leg to grid. (See Inset C)
5. Insert bolt upward through remaining hole in leg
and other pole. Fasten loosely with locknut. Repeat
by attaching other leg to pole. (See Inset D)
6. Complete assembly by tightening all bolts.
PAGE 1 OF 6
1-800-295-5510
uline.com
Grid Section x 1
Locknut x 8
Bolt x 8
PARTS
Pole x 2
ASSEMBLY
Inset A
Para Español, vea páginas 3-4.
Pour le français, consulter les pages 5-6.
Mounting Hardware
Bracket x 4
Spike x 8
(Mounting Optional, See Page 2)
Inset B
Inset C
Inset D
0721 IH-2540
Publicidad
Tabla de contenido
Manuales relacionados para Uline H-2540
Resumen de contenidos para Uline H-2540
- Página 1 Para Español, vea páginas 3-4. Pour le français, consulter les pages 5-6. H-2540, H-2541 1-800-295-5510 uline.com DOUBLE-SIDED GRID BIKE RACK TOOL NEEDED 9/16" Wrench PARTS Mounting Hardware Leg x 2 Grid Section x 1 Pole x 2 Bracket x 4...
-
Página 2: Tools Needed
2½". (See Inset A) (See Inset B) 2. Blow out the dust in the hole. 5. Repeat on remaining spikes. 3. Place bracket over tubing. Inset B Inset A 2½" 1-800-295-5510 uline.com PAGE 2 OF 6 0721 IH-2540... -
Página 3: Rack Portabicicletas De Rejilla De Dos Lados
H-2540, H-2541 800-295-5510 uline.mx RACK PORTABICICLETAS DE REJILLA DE DOS LADOS HERRAMIENTA NECESARIA Llave de 9/16" PARTES Accesorios de Instalación 2 Patas 1 Sección de Rejilla 2 Poste 8 Estacas 4 Soportes (Instalación Opcional, Vea Página 4) 8 Pernos 8 Contratuerca ENSAMBLE Inserte un perno hacia arriba a través del orificio... -
Página 4: Instalación (Opcional)
6.4 cm (2½"). (Vea Figura A) 5. Repita en las estacas restantes. 2. Sople para eliminar el polvo del orificio. 3. Coloque el soporte sobre el tubo. Figura B Figura A 6.4 cm (2½") 800-295-5510 uline.mx PAGE 4 OF 6 0721 IH-2540... - Página 5 H-2540, H-2541 1-800-295-5510 uline.ca SUPPORT À VÉLOS DE TYPE GRILLE À DOUBLE FACE OUTIL REQUIS Clé de 9/16 po PIÈCES Matériel d'installation Patte x 2 Section de grille x 1 Poteau x 2 Support x 4 Piquet x 8 (Installation facultative, à la page 6) Écrou freiné x 8...
-
Página 6: Outils Requis
5. Répétez la procédure pour les autres piquets. 2. Retirez la poussière du trou en soufflant dessus. 3. Placez le support sur le tube. Encadré B Encadré A 6,4 cm (2 ½ po) 1-800-295-5510 uline.ca PAGE 6 OF 6 0721 IH-2540...