Electrical Safety; Overview (Fig. A) - Black and Decker 7572 Manual Del Usuario

ENGLISH
When disposing of batteries, follow the instructions given
x
in the section "Protecting the environment".
Under extreme conditions, battery leakage may occur.
x
When you notice liquid on the battery, proceed as follows:
- Carefully wipe the liquid off using a cloth. Avoid skin
contact.
- In case of skin or eye contact, follow the instructions
below.
Warning! The battery fluid, a 25-30% solution of potassium
hydroxide, can be harmful. In case of skin contact, immediately
rinse with water. Neutralise with a mild acid such as lemon
juice or vinegar. In case of eye contact, rinse abundantly with
clean water for at least 10 minutes. Consult a physician.
Fire hazard! Avoid short-circuiting the contacts of a
detached battery (e.g. when storing the battery in a
toolbox).
Do not incinerate the battery.
Do not attempt to charge damaged batteries.
Chargers
Use your Black & Decker charger only to charge batteries
x
of the type supplied with your tool. Other batteries could
burst, causing personal injury and damage.
Never attempt to charge non-rechargeable batteries.
x
Have defective cords replaced immediately.
x
Do not expose to water.
x
Do not open the charger.
x
Do not probe the charger.
x
The charger is intended for indoor use only.

ELECTRICAL SAFETY

Your charger has been designed for a specific mains voltage.
Always check that the mains voltage corresponds to the
voltage on the rating plate.
Your charger is double insulated in accordance with
EN 60335; therefore no earth wire is required.
Warning! Never attempt to replace the charger unit with a
regular mains plug.
Additional safety instructions for hand-held saws
Always use the appropriate type of saw blade for the
x
workpiece material and type of cut.
Only use saw blades in good condition.
x
4
Always switch the tool off and wait for the saw blade to
x
come to a complete standstill before putting the tool down.
Keep your hands well clear of the saw blade while working.
x
Do not touch the saw blade immediately after the
x
operation as it might be hot.
Do not attempt to saw extremely small workpieces.
x
Before sawing in walls or floors, be aware of the location
x
of hidden pipes and wiring.
Never switch on the tool when the saw blade is jammed
x
in the workpiece or when it is in contact with the material.
Do not exert side pressure on the saw blade.
x
Always hold the tool with both hands.
x
Do not use the tool while in a tree, on a ladder or on any
x
other unstable surface.
When cutting branches be aware of where the branch will
x
fall.
Take special care when sawing woods and metal which
x
may produce toxic dust:
- Wear a dust mask specifically designed for protection
against toxic dust and fumes and ensure that persons
within or entering the work area are also protected.
- Do not let children or pregnant women enter the work area.
- Do not eat, drink or smoke in the work area.
- Dispose of dust particles and any other debris safely.

Overview (fig. A)

1. On/off switch
2. Lock-off button
3. Blade holder
4. Shoe
5. Blade clamp lever
6. Battery
7. Battery release button
8. Charger
9. Charger receptacle
Assembly
Fitting and removing the battery (fig. A)
To fit the battery (6), line it up with the receptacle on the
x
tool. Slide the battery into the receptacle and push until
the battery snaps into place.
To remove the battery, push the release button (7) while
x
at the same time pulling the battery out of the receptacle.
Fitting the saw blade (fig. B)
Hold the saw blade securely. If the saw blade is fitted with
x
a tooth protector, leave it attached while fitting the blade.
Pull the blade clamp lever (5) up to release the blade
x
clamping mechanism.
Insert the shank of the saw blade into the blade holder (3)
x
as far as it will go.