Rubi A230 PRO Manual Del Usuario página 11

Read the operating instructions
Protection category II power tool; double insulated
In accordance with essential applicable safety
standards of European directives
Wear eye protection
• Follow very carefully the instructions in this manual, save it
and keep it nearby, ready to carry out any inspection of parts
that may be necessary.
• If the tool is used with care and normal maintenance is carried
out, it will work well for a long time.
• The functions and use of the tool you have bought shall be
only those described in this manual. Any other use of the tool
is strictly forbidden.
ILLUSTRATIONS
DESCRIPTION (See figures)
1. Motor housing (Fig.1)
2. Gear housing (Fig.1)
3. Support plate (Fig.1)
4. Clamping nut (Fig.1)
5. Abrasive disc (Fig.1)
6. Disc guard (Fig.1)
7. Auxiliary handle (Fig.1)
8. Start-up switch (Fig.1)
9. Switch locking lever (Fig.1)
10. Spindle blocking button (Fig.1)
11. Rear handle turning button (Fig.1)
12. Handle (insulated gripping surface) (antivibrational)
(Fig.1)
13. Pin spanner (Fig.1)
EQUIPMENT
- Disc guard
- 1 auxiliary handle (antivibrational)
- 1 pin spanner
- Disc clamping nuts
- Operating instructions with Safety instructions
- Warranty
BRIEF DESCRIPTION
This angle grinder has been designed for cutting, deburring and
cutting metals and stone without the use of water.
English
ORIGINAL INSTRUCTIONS
BEFORE USING THIS TOOL
Before using the tool, make sure the mains voltage is correct: it
must be the same as that on the specification label. Machines with
230V can also be connected to a 220V mains supply.
FITTING SAFETY DEVICES
WARNING! Always unplug the machine before carrying out work
on it.
1) Fitting the disc guard
Insert the guard flange 6 in the slot in the collar of the machine
plate and turn it to the desired working position.
If the guard does not fit in the collar, loosen the bolt. Tighten
the lever. The guard can be moved manually to the marked
posi-tions. To remove the guard, perform the same steps in
reverse order.
WARNING! The closed part of the disc guard should always
point towards the user.
2) Fitting the auxiliary handle 7
Use of the auxiliary handle is obligatory in order to ensure
greater control and safety when handling the tool. The
auxiliary handle 7 must be screwed on to the right or left side,
depending on the type of work to be carried out.
3) Adjusting the Rear Handle 12
The rear handle 12 may be turned 90º to the left and to the
right in relation to the motor housing.
This enables the ON/OFF switch to be turned to the most
suitable working position.
To turn the rear handle, follow the instructions below:
- Press the rear handle turning button 11 and, at the same
time, turn the rear handle 12 to the left or right until it locks.
- To return to the initial position, do the same in reverse.
FITTING THE ACCESSORIES (DISCS AND
WHEELS)
WARNING! For safety reasons, the machine should always be
unplugged from the mains before changing the disc or wheel.
Always work with the guard on and wear safety goggles.
Use deburring and cutting discs with fibre-reinforced synthetic
binders, for a maximum peripheral speed of 80 m/s and cup wheels
with synthetic binder for 45 m/s. Protect discs and wheels from
knocks and blows.
WARNING! Never press the blocking button when the machine
is running. The shaft must have stopped completelybefore the
blocking button is pressed.
To fit the disc, proceed as follows:
1. Block the spindle (shaft), by pressing the blocking button 10.
2. With the pin spanner 13, remove the clamping nut 4 from the
spindle.
3. Fit the abrasive disc on the support plate 3.
4. Replace the clamping nut 4, using the pin spanner 13. The
position of the nut 4 will depend on the thickness of the disc.
5. Once the disc is fitted, check that the blocking button has
returned to its original position due to movement of the
incorporated spring.
11.