Publicidad
Idiomas disponibles
Idiomas disponibles
Installation and Operating Instructions
Dimplex Air Barrier - Switch Panels
Models : CABC1 & CABC2
IMPORTANT : THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Model(s)
(All Electrically Heated CAB
CABC1
& DAB models)
CABC2
(All Water & Ambient Heated
CAB & DAB models)
Important Safety Advice
Always disconnect the supply before working on the
product.
This product should be mounted safely onto a
suitable wall.
Ensure that cables are of adequate current carrying
capacity.
The switch module should not be installed in a toilet or
washroom.
WARNING: Isolate electrical supply to ALL modular linked
units when carrying out maintenance.
Electrical
The installation of this appliance should be carried out by a
competent electrician and be in accordance with the current IEE
wiring regulations.
Installation
The backing box (standard double gang) should be rebated into a
suitable wall - Fig. 7. The box should be fitted so that the switch panel
will be flush with the wall. Suitable conduit should be used where
applicable to carry the cable between the heater and the switch
panel.
The cable used to connect the heater to the low voltage switch
panel should have sufficient cores to allow connection as per the
enclosed wiring diagram and be of a size between 0.22mm² and
1.0mm².
(Typically 9 core for electrically heated models and 5 core for water
heated / ambient models).
Test all switch settings once installation is complete.
Connections – To the Switch Panel
The cable should be connected as per the Wiring Diagrams shown -
see Fig. 2 for CABC1 and Fig. 3 CABC2.
Tip: When stripping back the switch cable make note of the
numbering or colours of the wires and their associated
connections to the terminal block.
Wiring
see Fig. 2 for Wiring Diagram for CABC1 Model
Switch No. Description
1
ON - OFF
2
LOW FAN - HIGH FAN
3
FULL HEAT - NO HEAT - HALF HEAT
4
MANUAL - AUTOMATIC
5
TERMINAL BLOCK
C
CABLE TO PCB (NOT SUPPLIED)
D
DOOR SWITCH (NOT SUPPLIED)
T
OPTIONAL THERMOSTAT (NOT SUPPLIED)
A
B
C
85mm 120mm
145mm
145mm
85mm 120mm
( see Fig. 1 )
- 1 -
see Fig. 3 for Wiring Diagram for CABC2 Model
Switch No. Description
1
ON - OFF
2
LOW FAN - HIGH FAN
4
MANUAL - AUTOMATIC
5
TERMINAL BLOCK
C
CABLE TO PCB (NOT SUPPLIED)
D
DOOR SWITCH (NOT SUPPLIED)
Connections – To the appliance's PCB
Gain access to the PCB by removing the outlet grilles, bottom panel
and pressure plate - refer to the CAB/DAB Installation and Operating
Instructions.
Remove a 'knock out' from the centre of the top panel of the heater
(see 'x' in Fig. 4a for the Electric model and 'x' in Fig. 4b for the
Water/Ambient model) and feed the switch cable ('a' in Fig. 5) into
the heater using an appropriate cable gland (not supplied) to fix the
cable. Replace the pressure plate (on 'CAB' model only) and tie the
cable using the tie wrap and fixing clip supplied to the pressure plate
at 'b' in Fig. 5. If necessary tie the stripped cable at 'c' in Fig. 5.
WARNING: Ensure cable path does not come into
contact with heater element.
Connect the cable to the appropriate connections - see
'y' in Fig.4a and Fig.4b. See Fig. 6 for detail view of PCB connection.
Replace the bottom panel and air outlet grilles.
Operation
The desired setting can be obtained through switch selection. Refer
to the CAB/DAB instruction leaflet for further details.
Cleaning
WARNING: DISCONNECT SUPPLY before carrying out
maintenance.
External appearance can be maintained by wiping occasionally with
a damp cloth ; for stain removal, a weak soap solution can be applied
with a cloth and the surface wiped dry. Care must be taken to avoid
any moisture ingress into the product.
After Sales Service
Should you require after sales service or should you need to purchase
any spares, please contact the retailer from whom the appliance
was purchased or contact the service number relevant to your
country on the warranty card.
Please do not return a faulty product to us in the first instance as this
may result in loss or damage and delay in providing you with a
satisfactory service.
Please retain your receipt as proof of purchase.
UK
Publicidad
