Frequently Asked Questions - Car Keys Express Simple KEY CDPXA-7020 Guia De Inicio Rapido

SIMPLE™ KEY USER GUIDE
2. Using your ACTIVATION CODE found in the chart on page 3, enter
the first digit using the LOCK button, the second digit using the
PANIC button, and the third digit using the UNLOCK button.
For example, KEY CODE 314 is entered by pressing the LOCK
button three (3) times, the PANIC button one (1) time, and then the
UNLOCK button four (4) times.
3. Now, press the LOCK button on the remote.
a. The light will now blink back the ACTIVATION CODE you originally
entered. If this does not match, go back to Step 1 to start over.
For example, the indicator light for KEY CODE 314 will blink (3) times,
pause, blink one (1) time, pause, and finally blink four (4) times.
b. If the light blinks rapidly, this indicates an error. Go back to
ACTIVATION step 1 and retry the steps using your ACTIVATION CODE.
NOTE: You may re-enter activation codes anytime before the
key is paired to your vehicle. After the key is paired to your
vehicle, do not attempt to re-enter or change the button code.
This will cause the key to not work.
4. Move on to STEP 2 (of 2) below to PAIR the key to your vehicle.
STEP 2 (OF 2) KEY PAIRING
Instructions have timing requirements. If you wait too long between steps,
your vehicle's computer may time out, requiring you to start over. Once
you begin the pairing procedure, move at a quick and even pace.
NOTE: If the EZ Installer™ is left in the vehicle's on-board diagnostic
(OBD) port for more than 5 minutes, an alarm will sound reminding you to
remove it.
NOTE: If at any point the EZ Installer™ continues to beep rapidly, please
refer to the FAQ section for more information.
1. Find your vehicle's make, model, and year in the Compatibility Lookup
on page 3. Turn the dial on the EZ Installer™ to the position listed for
your vehicle's make, model, and year.
a. NOTE: One working key and the new key should be present
during the pairing process.
2. Enter the vehicle and ensure all doors are closed.
4
SIMPLE™ KEY USER GUIDE
3. Begin with the vehicle in PARK and the engine OFF.
4. Turn hazard lights ON.
5. Using an existing, working key, start the car.
6. Remove the security label from the EZ Installer™ and insert it firmly
into the on-board diagnostic (OBD) port located under the dash.
NOTE: The location of your vehicle's OBD port can be found in
a.
your vehicle owner's manual.
7. Wait up to 8 seconds and listen for 3 quick beeps from the EZ
Installer™.
a. NOTE: If you hear a series of more than 3 rapid beeps, an error
has occurred. Please see the Frequently Asked Questions to
learn more.
8. Turn the ignition off.
9. To continue, press and release the EZ Installer™ button.
10. Press the UNLOCK button on the new remote 10 times at 1 second
intervals. (Tip: You can sync your pressing of the button with the
blinking of your hazard lights.)
NOTE: If you hear 3 quick beeps from the EZ installer while you
a.
press the UNLOCK button, stop and skip to step 12, otherwise
continue to step 11.
11. Wait up to 5 seconds. If you don't hear 3 quick beeps from the EZ
Installer™, continue pressing the UNLOCK button on the new remote at
1 second intervals until you hear 3 quick beeps from the EZ installer.
a. NOTE: If you hear a series of more than 3 rapid beeps, an error
has occurred. Please see the Frequently Asked Questions to
learn more.
12. Press and release the EZ Installer™ button to continue. The EZ
Installer™ will chime when pairing is complete.
13. Unplug the EZ Installer™. If the EZ Installer™ is left in the OBD port for
more than 5 minutes, an alarm will sound, reminding you to remove it.
14. To pair additional keys, unplug the EZ Installer™ from the OBD port
and reinsert it. Repeat the pairing process for any additional keys,
beginning with PAIRING STEP 1.
15. Test all keys.
16. Turn hazards off.

FREQUENTLY ASKED QUESTIONS

Q: The EZ Installer™ beeps 8 times after pushing the button to start the
pairing process and will not pair the new key.
A: Your vehicle allows a maximum of 8 paired keys. If the vehicle already
has 8 keys paired to it, a new key cannot be paired. If the EZ Installer™
beeps 8 times early in the pairing process, this indicates that the maximum
number of keys have been paired. Please contact Car Keys Express
customer service at 888-598-8910.
5