Westin 33-1280 Manual De Instrucciones

AUTOMOTIVE PRODUCTS, INC.
BULL BAR ASSEMBLY
ENSAMBLE DE PARRILLA
DELANTERA CON TIRÓN
LA BULL BAR
33-1280
33-1285
ITEM QTY
1 1 BULL BAR ASSEMBLY
2,3 2 BRACKET, PASSENGER (2) AND DRIVER (3)
4 2 PLASTIC PLUG
5 4 RUBBER BUMPER
6 2 1/2-13 X 2.00" HEX HEAD BOLT
7 2 1/2" FLAT WASHER
8 2 1/2" LOCK WASHER
9 6 M10-1.25 FLANGE NUT
1 1 ENSAMBLE DE PARRILLA DELANTERA CON TIRÓN
2,3 2 SOPORTE
4 2 TAPONES DE PLÁSTICO
5 4 PARACHOQUES DE HULE
6 2 PERNOS CON CABEZA HEXAGONAL DE
7 2 ARANDELA PLANA SAE DE 1/2"
8 2 ARANDELAS DE PRESIÓN DE
9 6 TUERCAS CON BRIDAS M10-1,25
1 1 LA BULL BAR
2,3 2 SUPPORT, PASSAGER (2) ET CONDUCTEUR (3)
4 2 BOUCHON DE PLASTIQUE
5 4 PARE-CHOCS EN CAOUTCHOUC
6 2 BOULON A TETE HEXAGONALE
7 2 RONDELLE PLATE SAE 1/2 PO
8 2 RONDELLE A FREIN 1/2 PO
9 6 ÉCROU D'ACCOUPLEMENT M10-1,25
Remove the contents from box and check for damage. Verify all parts are present. Read instructions
STEP 1.
completely before beginning.
NOTE: It will be necessary to remove the front license plate and bracket. Remove license plate from
STEP 2.
bracket. Using a 3/16" drill bit, drill out the two pop rivets that hold the bracket to the bumper. If
local/state laws requires a license plate, license plate relocation kit 32-0055 is available.
Locate factory bolts that hold the bumper support frame to vehicle frame.
STEP 3.
Position brackets onto factory bolts and secure using M10-1.25 flange nuts. Leave loose. NOTE: Bracket
STEP 4.
will sit on top of existing nuts.
Attach bull bar hoop to brackets with 1/2" fasteners. Level and adjust Bull Bar as desired and tighten all
STEP 5.
fasteners. Recommended torque values are 64 Ft. Lbs. for 1/2" yellow zinc fasteners and M10-1.25
flange nuts to 32 Ft.Lbs.
LIGHT INSTALLATION: Insert threaded stud on base of the light through hole in cross tube. Using a ratchet, extension
and socket for correct size of nut supplied, insert through large clearance hole in bottom of cross tube.
Thread nut and washers on stud and tighten. SEE FIGURE 1. NOTE: A short socket, not a deep well works
best to get the nut started.
NOTE: Fits most 6" round or rectangle lights. Some lights may require replacing included mount/isolator with
rubber bumpers provided. Mounting stud of 1/2" or less required. Plug mount holes with caps provided if
not installing lights.
FINISH PROTECTION
Westin products have a high quality finish that must be cared for like any other exposed finish on the vehicle. Protect the finish with a non-abrasive automotive wax, (e.g. Pure Carnauba)
on a regular basis. The use of any soap, polish or wax that contains an abrasive is detrimental, as the compounds scratch the finish and open it to corrosion.
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
APPLICATION: 2003-08 TOYOTA 4-RUNNER
APLICACIÓN: TOYOTA 4-RUNNER, MOD. 2003-08
APPLICATION: 2003-08 TOYOTA 4-RUNNER
1
CONTENTS - CONTENIDO - CONTENU
, ACOMPAÑANTE (2) Y CONDUCTOR
1/2"
1/2-13 X 2,00
(3)
1/2-13 X 2,00"
PO
2
TOOLS - HERRAMIENTA - OUTILS
3/4'' SOCKET
15MM SOCKET
15MM WRENCH
RATCHET
TORQUE WRENCH
DADO DE 3/4´´
DADO DE 15MM
LLAVE DE TUERCAS DE 15MM
MANERAL
EXTENSIÓN PARA DADO
LLAVE DE TORQUE
DOUILLE 3/4 PO
DOUILLE 15MM
CLEF 15MM
CLIQUET
RALLONGE DE DOUILLE
CLE DE COUPLE
WO:
75-0717 REVISION A 3/18/08
3