Publicidad
Idiomas disponibles
Idiomas disponibles
LCD Programmable Thermostat
Code: 0769010, Reference: KT10-LCD-P
A.
Installation, Mounting:
CAUTION:
1. Turn off 0769010, electronic source and the electrical devices (e.g. heater) which
will be connected before installation and maintenance.
2. The installer must be a trained service engineer
1. Installation Location:
The thermostat should be mounted on an inner wall 1.5m above the floor in position
where it is readily affected by changes of the general room temperature with freely
circulating air. Prevent direct exposure to sunlight; dripping or splashing area. Do not
place this unit at a location where air circulation is low, or where it has great
temperature changes (e.g. near door). Do not place the thermostat near heat generating
sources (radiators, hot air vents, TV or lights).
2. Wiring:
For 0769010, there are 3 wiring terminals at the bottom which is labeled as "L", "1"
and "N". Connect a heater to the "1" and "N". It is high recommended that the wiring
connection to the supply is via a fuse rated at no more than 15 Amps.
Push all cables back into wall prior to fixing to avoid trapping wires.
Do not use metal conduit or of cable provided with a metal sheath.
Recommend adding Fuse or protective device in the live circuit.
3. Mounting:
○
○
,1 and
,2.
1. Loosen the screws of cover as
○
○
2. Take off the cover in direction as
,3 and
3. Place the cables at the hole near the terminal block (Please refer to the Wiring
section)
4. Mounting without bottom plate (Diagram 1):
- Ensure the surface is level
- Place the cable at the hole near the terminal block
- Place the 2 pcs of wall anchors into the holes of the wall
- Fasten the thermostat with 2 pcs of long screws though the 2 mounting holes
5. Mounting with bottom plate (Diagram 2):
- Adjust the bottom plate on the wall or junction box and ensure the plate is at surface
level and cover the junction box comfortably
-
If necessary, pull the cables out at the middle hole of the bottom plate
-
Place the 2pcs of wall anchors at the wall if necessary
-
Fasten the plate with the 2pcs of long screws
-
Place the cables at the hole near the terminal block
-
Fasten the thermostat with the 2pcs of screws through the 2 mounting holes
6. Ensure the rubber key is firmly on the PCB as
7. Ensure the rubber key fitting location on the cover is right towards to rubber key as
○
,5b.
8. Reinstall the cover as
9. Fasten the screws of cover as
Check the rubber key can be pressed smoothly, otherwise reinstall the cover and realign
properly.
B. Start/Reset:
1. Switch off all the connected devices, after wiring and mounting.
2. The main electric source is switched ON, the LCD display will be switch ON.
3. The 0769010 will be ready to control the heater.
4. Switch ON the heater. The heater will remain OFF until 0769010 activates the output
ON with
C. Normal Time Mode:
1. Temperature detection starts and LCD displays the room temperature.
2. Defrost function is activated with
will be forced to ON @ Heat.
3. Below 0°C, 0769010 will display LO.
4. Above 40°C, 0769010 will display HI.
D. Normal Time Setting Mode:
1. Press <
of Week.
2. Press <
3. Press <
4. Press <
5. Press <
Or 0769010 will auto-return to normal mode after 10 seconds.
E. Factory Defined Programs:
The heater turns on according to the activated program and the control temperature setting.
When the heater is On, Program number and
The pre-defined programs are as below:
P1
P2
P3
P4
F. Set Program:
1. Press <PRG>, the hour will flash, press < >, < > to change the hour setting.
2. Press <PRG>, the minutes will flash, press < >, < > to change the minutes setting.
3. Press <PRG>, temperature will flash, press < >, < > to change the setpoint.
4. Press <PRG> to set the next program.
5. The program setting sequence is as below:
Mon~Fri (P1 P2 P3 P4) Sat (P1 P2 P3 P4)
,4.
Sun (P1 P2 P3 P4)...
6. Press <
or 0769010 will auto-return to normal mode after 10 seconds.
G. Temporary / Permanent Override Mode:
There are two modes in the override mode (Temporary override and Permanent override
mode). Press < HOLD > to select the override mode.
The sequence is as below:
Normal Temporary Override Permanent Override Normal...
○
,5a..
○
○
,6 and
,7.
○
○
,9 and
,10.
displayed on LCD.
displayed when temperature is 5°C or below. Output
>, the Day of Week (1-7) will flash, press < >, < > to select the current Day
>, the Hour will flash, press < >, < > to set the Hour.
>, the Minute will flash, press < >, < > to set the Minute.
> will jump back to the step 1.
> to confirm the settings and return to Normal Mode.
icons are shown.
Mon ~ Fri
Sat
06:00 (21°C)
08:00 (21°C)
08:00 (16°C)
10:00 (16°C)
18:00 (21°C)
18:00 (21°C)
22:00 (16°C)
23:00 (16°C)
> to exit the program mode setting and return to the normal mode.
Selecting the Temporary/ Permanent Override Mode
1. Press < HOLD >
to
change the mode from normal to Temporary Override.
icon will be displayed.
2. Press < HOLD > again, the mode changes from Temporary Override to
Permanent Override mode.
3. Press < HOLD > once, the mode changes from Permanent Override to normal
mode.
Review and adjust the Override temperature:
1. Press < >/< >, the Override temperature is shown.
2. Hold the < >/< > for 2 seconds, the Override temperature will flash.
3. Press < >/< > to adjust the Override temperature.
4. Press <
> to exit the Override temperature setting.
Or 0769010 will auto-return to normal mode after 10 seconds.
Temporary Override Mode:
Temporary Override mode maintains until next program time is met.
Permanent Override Mode:
The room temperature will be maintained at the Override temperature until
Override mode is released. Press < HOLD > to release the Permanent
Override mode.
H. Control Off / Sleep mode:
1. Press the <
> to select the sleep mode and control off mode. The sequence is
as below:
Normal Mode Sleep Mode Control Off ModeNormal Mode ...
2. Press any other keys to exit the control off / Sleep mode and return normal
mode.
Sleep mode:
At sleep mode, <
> icon is displayed. The heater is turned off, irrespective of
the current control setting temperature. The temperature and real time are
shown. The defrost function is activated when temperature is 41°F or below.
Output will be forced to ON @ Heat.
Control Off mode:
The LCD is fully turned off. The heater is switched off, irrespective of the
current control temperature setting. The defrost function is disabled.
I. Jumper selection:
Delay / No Delay jumper:
No delay
Delay
Choose the Delay option if compressor heat is connected.
12-hours / 24-hours mode jumper:
When the 12-hours option is selected, the time is shown in 12-hours mode.
Otherwise, the time is shown in 24-hours mode.
J. Specification:
1. Temperature measurement: 0.0 – 40.0°C
Sun
2. Accuracy:
08:00 (21°C)
3. Temperature control range:
10:00 (16°C)
4. Resolution:
6. Switching differentia:
18:00 (21°C)
7. Rating:
23:00 (16°C)
8. Terminals:
9. Electronic control:
10. Operating temperature:
11. Storage temperature:
12. Sensing Element:
13. Pollution degree:
TEMPER ENERGY INTERNATIONAL S.L.
Polígono industrial de Granda, nave 18
33199 • Granda - Siero • Asturias
Teléfono: (+34) 902 201 292
Fax: (+34) 902 201 303
Email: info@grupotemper.com
www.grupotemper.com
icon will be displayed.
Heater
10sec
4mins
± 0.5°C
5.0 – 35.0°C
0.5°C
± 0.5°C
230Vac~ 50/ 60Hz 15(3)A max
2
2mm
cable
Type 1B action
0 - 50°C
0 - 60°C
NTC thermistor
2
141009
Publicidad
