Campingaz Lumostar Plus Manual De Instrucciones página 7

INSTRUCTIONS FOR USE
Rate: 38 g/h (0,52 kW) - injector nº 019605
Category: butane direct pressure
Thank you for choosing the Campingaz
A - IMPORTANT : ALWAYS BE CAREFUL WHEN
USING GAS !
The purpose of these instructions is to enable you to use
®
your Campingaz Lumostar
plete safety.
Please read them carefully to familiarise yourself with
the equipment prior to assembling the gas container.
Please observe these instructions and the safety measu-
res printed on the Campingaz
PLUS / CV 470 PLUS cartridges. Failure to observe these
instructions may result in the user and people in the
immediate vicinity being put at risk.
Keep these instructions in a safe place so that you can
refer to them if needed.
This equipment must be used exclusively with
®
Campingaz CV 270 PLUS / CV 300 PLUS / CV 470 PLUS
cartridges. Using other gas containers may be dange-
rous.
The Société Application Des Gaz (Gas Enforcement
Company) accepts no responsibility where cartridges of
any other make are used.
This equipment must only be used in adequately ventila-
ted areas (minimum 2 m
3
from any flammable material.
Do not use equipment which leaks, functions incorrectly
or is damaged. Return it to your retailer who will inform
you of your nearest after-sales service.
Never modify this equipment or use it for purposes for
which it is not intended.
Do not use this product in caravans, cars, tents, huts,
sheds or any small enclosed areas.
The product should not be used while sleeping or left
unattended.
This product consumes fuel through combustion or
consumption of oxygen and gives off certain substances
and gas, which could be dangerous such as carbon
monoxide.
Carbon monoxide is an odorless, clear gas that can
cause flu-like symptoms, sickness, illness, and possibly
death if produced inside aforesaid enclosed areas
through use of the product without proper ventilation.
B - PUTTING INTO OPERATION
1) INSTALLING THE CAMPINGAZ
PLUS / CV 470 PLUS CARTRIDGE
(Where the existing cartridge is empty, read paragraph D :
"Removing the cartridge")
When installing or changing a cartridge, always operate in a
very well-ventilated location, preferably outside, never near a
flame, heat source or spark (cigarette, electric apparatus,
etc.) and far away from other people and inflammable materials.
®
AS CAMPINGAZ CV 270 PLUS / CV 300 PLUS / CV 470
PLUS CARTRIDGES ARE VALVE-OPERATED, THEY CAN
BE DETACHED FROM THE EQUIPMENT, EASILY TRANS-
PORTED (EVEN WHEN NOT EMPTY) AND FITTED TO
®
OTHER CAMPINGAZ EQUIPMENT IN THE 270 PLUS /
300 PLUS / 470 PLUS RANGE DESIGNED TO OPERATE
EXCLUSIVELY WITH THESE CARTRIDGES.
® ®
Lumostar Plus
®
Plus correctly and in com-
®
CV 270 PLUS / CV 300
/h/kW) and at a good distance
®
CV 270 PLUS / CV 300
a) Check that the gas supply is fully turned off by turning the
control wheel (1) clockwise as far as the handle ("-" direction
of the arrow) (fig.2).
b) Hold the stove (Caution - it may be hot!) and gently screw the
cartridge onto the stove clockwise until you hear a click (about
one sixth of a turn) (fig. 3). Do not tighten the cartridge further,
as you may damage its valve.
2) Fitting the mantle
a) Unscrew the nut (6) on the top of the lid (5) and remove it (Fig.
4).
b) Remove the cage + glass assembly (Fig. 5) (caution: it may
be hot!).
c) Slide the mantle (7) onto the burner, with the larger hole
facing downwards; slot the mantle into the grooves of the bur-
ner (fig.6).
3) Burning the mantle for the first time (do this outside)
a) DO NOT SWITCH ON THE GAS, hold a naked flame (ciga-
rette lighter or match) close to the mantle.(7)(fig.7)
b) Allow it to burn up completely (smoke is given off) until it looks
like a black ball (fig. 5).
c) Reinstall the cage + glass assembly (Fig. 8):
Important: the burned sleeve is extremely fragile, make sure
you do not touch it when reinstalling the cage + glass assem-
bly.
- Make sure that the glass (3) is wedged correctly at the bottom
of the cage and held firmly by the spring.(fig. 10)
- Insert the cage + glass assembly into the lamp, taking care to
position the tongue "L" in the lower cup (8) correctly in the slot
located underneath the cage (4) (Fig. 8).
- Check that the cage + glass assembly is inserted correctly in
the lower cup (8) and that the tongue "L" is inserted correctly
in the slot provided for this purpose (Fig. 8).
- Reinstall the nut (6) on top of the lid (5) and screw it onto the
central burner rod (Fig. 8).
The lamp is now ready to operate.
4) Changing the glass (caution: the equipment may be hot!)
a) Unscrew the nut (6) on the top of the lid (5) and remove it (Fig. 4).
b) Remove the cage + glass assembly (Fig. 5) (caution: it may
be hot!).
c) Remove the handle (2) by unfolding its arms so that they slip
out of their housing located on either side of the lid. Caution:
keep the handle horizontal so that the arms are in line with the
slots on the lid (Fig. 9).
d) Remove the lid (5) by unfolding the tabs anchored to the cage
slightly (Fig. 11).
e) Change the glass taking care to push it firmly into the lower
cup in the cage (largest diameter hole towards the bottom).
Make sure the spring penetrates inside the glass (the spring
must be vertical to the inside of the glass (Figs. 12 and 10).
f) Put the lid (5) back in place.
g) Reinstall the cage + glass assembly (see paragraph B -3 c
and Figure 8).
7
GB