Flight Control - Revell Control Hexatron FPV Manual Del Usuario

6 TrIM aDJuSTMeNT oF The CoNTrol
The correct trim is a basic requirement for fault-free flying behaviour of the multicopter.
Its adjustment is simple, but it requires some patience and a feel for it. Please observe
the following instructions precisely: Carefully move the thrust control up and raise the
multicopter approximately 0.5 to 1 metre in altitude.
6A If the multicopter moves by itself slowly or quickly to the left or right ...
press the trim adjustment for banking incrementally in the opposite direction.
6B If the multicopter moves by itself slowly or quickly around its own axis ...
press the trim adjustment for rotation incrementally in the opposite direction.
6C If the multicopter moves by itself slowly or quickly forwards or
backwards ...
press the trim adjustment for forward and backwards flight incrementally in the
opposite direction.

7 FlIghT CoNTrol

Note: Only minimal corrections of the controls are necessary for a smooth flying
behaviour of the multicopter! The direction information applies if the multicopter is
viewed from behind. If the multicopter is flying towards the pilot, it must be moved in
the opposite direction.
7A Mode 2: Take off or increase altitude by carefully moving the LEFT control for thrust
and rotation forward.
Mode 1: Take off or increase altitude by carefully moving the RIGHT control for
thrust and rotation forward.
7B Mode 2: Land or decrease altitude by carefully pulling back on the LEFT control for
thrust and rotation.
Mode 1: Land or decrease altitude by carefully pulling back on the RIGHT control
for thrust and rotation.:
7C Mode 2: Fly forward by moving the RIGHT control for forward/backward flight and
sideways flight carefully forward.
Mode 1: Fly forward by moving the LEFT control for forward/backward flight and
sideways flight carefully forward.
7D Mode 2: Fly backwards by carefully pulling back on the RIGHT control for forward/
backward flight and sideways flight.
Mode 1: Fly backwards by carefully pulling back on the LEFT control for forward/
backward flight and sideways flight carefully.
7E Fly to the left by moving the controller for forward/backward flight and banking
carefully to the left.
7F Fly to the right by moving the controller for forward/backward flight and banking
carefully to the right.
7G Turn helicopter around to the left by moving the controller for thrust and rotation to
the left.
7H Turn helicopter around to the right by moving the controller for thrust and rotation
to the right.
18
Higher flight speed
Each time you press the button on the left shoulder on the remote, the flight is
increased one increment of 50%, 60%, 80% and 100% (7I). Now the multicopter has
a greater tilt, which enables higher flight speed. Please do not use this function until
you have gained sufficient experience in the standard setting, because the
multicopter is very sensitive, which makes a fine touch necessary when controlling it.
Fly loops - advanced users only! When you have sufficiently mastered your
multicopter, you can try your hand at the stunt flying function. For maximum speed,
press the button for flight speed until 100% flashes on the display. Make sure that you
have sufficient room in each direction (at least 10 metres). Also observe the safety
height - fly at a height of at least 5m, as your multicopter loses height when rolling
over and has to be caught and corrected afterwards!
Note: Looping is more successful when the battery capacity is near full.
Now climb to safety height. Press the control for forward and backwards flight
and banking all the way forward and all the way back very quickly.
The multicopter performs a forward looping manoeuvre - looping in other directions
are performed corresponding to the movement of the controller. Be prepared to catch
the multicopter, as the flying height, direction and speed after rolling over depend
heavily on the wind and preceding flight movements.
Photo and video function
Flight videos can be recording to a micro SD memory card during flight. Briefly press
the lower button (7K) on the round button panel to the right of the display to take a
photo. Video recording is started by pressing the top button (7J) on the round button
panel. Pressing it again stops the recording.
In order to be able access the video, the memory card must be removed from the
video transmitter and inserted into the USB card reader (7L). The driver installs
automatically when it is inserted into any USB port on a computer. After the automatic
installation, photos and videos can be opened and edited.
19