Product Familiarisation - Silverline 633706 Manual De Instrucciones

GB
Introduction
Thank you for purchasing this Silverline tool. This manual contains information necessary
for safe and effective operation of this product. This product has unique features and, even if
you are familiar with similar products, it is necessary to read this manual carefully to ensure
you fully understand the instructions. Ensure all users of the tool read and fully understand
this manual.
Description of Symbols
The rating plate on your tool may show symbols. These represent important information about the
product or instructions on its use.
Wear hearing protection.
Wear eye protection.
Wear breathing protection.
Wear head protection.
Wear hand protection.
Read instruction manual.
Specification
Chuck capacity:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10mm (3/8")
Shank length: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30mm (1-3/16")
Cut hole diameter: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 - 200mm (1-9/16" – 7-7/8")
Max speed: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .500rpm
Dimensions (L x W x H):. . . . . . . . . . . . . . .300 x 300 x 250mm (11-3/4" x 11-3/4" x 9-3/4")
As part of our ongoing product development, specifications of
Silverline products may alter without notice.
Hole Cutter Safety
WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and
instructions may result in a serious injury, or damage to the tool.
WARNING: Always adhere to all safety advice and instructions for any power tool used in
conjunction with this product.
WARNING: Do not exceed the maximum rated speed of the hole cutter. Running faster than the
rated speed may cause serious injury, or damage to the tool.
• Wear approved eye protection, hearing protection and breathing protection when using this tool
• Ensure around and behind the cutting area is free from any hazard such as electrical cables or
pipework before drilling
• Remove any adjusting key or wrench before turning the powered tool ON
6
Original Instructions

Product Familiarisation

1. Cutter Shaft
2. Cowling Nut
3. Spring
4. Cutter Positioning Bar
5. Cutter Holders
6. Cowling
7. Cowling Collar
8. Hex Key 3mm
9. TCT Blades
10. Carbon Steel Blades
11. Lip and Spur Drill Bit
12. Masonry Drill Bit
13. Drill Holder
Intended Use
Adjustable hole cutter with cowling for drilling 40 – 200mm diameter holes. Suitable for use with
wood, plastic, plasterboard, aluminium and acrylic sheets.
Before Use
Attach the cowling (Fig. I)
IMPORTANT: The Cutter Shaft (1) uses a reverse thread (left-hand thread) to prevent loosening when
in use. To unscrew the Cowling Nut (2), turn in a clockwise direction; and to tighten, screw in an
anti-clockwise direction (Fig. II).
1. Remove the Cowling Nut and Spring (3) from the Cutter Shaft
2. Insert the top of the Cutter Shaft through the Cowling Collar (7) from the inside
3. Place the Spring over the Cutter Shaft and screw on the Cowling Nut until it is secure fully
covering the thread on the Cutter Shaft
Changing the drill bit
Drill bits supplied:
• Carbon Steel Lip and Spur Auger Drill Bit 8mm (11) for use with wood
• TCT Masonry Drill Bit 10mm (12) for use with brick and plasterboard
1. Select the correct drill bit for the material to be cut
2. Loosen the hex screw securing the drill bit in the Drill Holder (13), using the Hex Key (8)
3. Remove the existing drill bit and insert the replacement drill bit
4. Tighten the hex screw sufficiently to secure the drill bit
Changing the cutters
Cutter blade types supplied:
• TCT Blades (9) suitable for harder materials
• Carbon Steel Blades (10) suitable for softer materials
1. Select the correct cutter blade for the material to be cut
2. Loosen and remove the hex screw securing the cutter in the Cutter Holder (5)
3. Remove the existing cutter and insert the replacement cutter
Note: The TCT Blades should be inserted with the bevelled cutting edge facing the direction of
travel – clockwise (Fig. III). The Carbon Steel Blades should be placed with the flat side facing
inwards (Fig. IV).
4. Tighten the hex screw sufficiently to secure the cutter blade