Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: F24735
Wrenches: (2) 3/4"
Drill Bits: NONE
OPTIONAL BLOCK
USE AS NEEDED
BLOCKS
BOLT STACKING DRIVER SIDE
FIGURE 2
1
Qty. (2)
BOLT – HEX HEAD 1/2-13 X 2.50"
2
Qty. (2)
WASHER FLAT 1/2"
3
Qty. (6)
BLOCK – 1/4 X 1 X 1-1/2
4
Qty. (4)
WASHER CONICAL
1. Raise hitch and loosely secure it to the outside of the drivers side tie down bracket (bolting through the top bracket hole), and inside
of the passenger side tie down bracket (bolt through the bottom bracket hole). See figures 1,2,& 3 for fastener orientation.
2. Swing the hitch rearward aligning the bars and the spacers with the corresponding holes in the impact bar. Install 1/2-13 x 6.50"
bolts and conical toothed washers through the bars and spacers as shown.
3. Tighten all fasteners to the required specifications.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2006 Cequent Towing Products
Installation Instructions
SUBARU BAJA
FASCIA
Drawbar Kit:
3590
Drawbar must be used in the
RISE position only.
NOTE TO OWNER: DO NOT TOW
WITH TAILGATE DOWN. DAMAGE
TO TAILGATE MAY ACCURE
EXISTING WELD NUT
1
2
3
4
5
DRIVER SIDE
BRACKET HOLE
PASSENGER SIDE
BRACKET HOLE
Tighten all 1/2-13 x 6.50 fasteners with torque wrench to 50 Lb.-Ft.
Tighten all other 1/2-13 fasteners with torque wrench to 75 Lb.-Ft.
Do Not Exceed Lower of Towing Vehicle
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Wiring Access Location: SUV1, SUV2
IMPACT BAR
BAR
6 47
FIGURE 1
5
Qty. (2)
NUT HEX 1/2-13
6
Qty. (2)
SPACER
7
Qty. (2)
BOLT – HEX HEAD 1/2-13 X 6.50"
8
Qty. (X)
Xxxx
Sheet 1 of 3
N24735
Part Numbers:
Manufacturer's Rating or
1
2
3
4
OPTIONAL BLOCK
5
USE AS NEEDED
TIE DOWN
BRACKET
SPACER
BRACKET
BOLT STACKING PASSENGER SIDE
FIGURE 3
05/30/06
Form F206 Rev A 5605
24735
77051
60982
BLOCKS
TIE DOWN BRACKET
Rev. C
Publicidad
Manuales relacionados para Cequent Towing Products 24735
Resumen de contenidos para Cequent Towing Products 24735
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 N24735 05/30/06 Rev. C 2006 Cequent Towing Products Form F206 Rev A 5605...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 N24735 05/30/06 Rev. C 2006 Cequent Towing Products Form F206 Rev A 5605...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684 Hoja 3 de 3 N24735 05/30/06 Rev. C 2006 Cequent Towing Products Form F206 Rev A 5605...