Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Frame rail
Plate
Hitch Shown In Proper Position
Equipment Required: Sealant
Fastener Kit: 24796F
Wrenches: 11/16", 5/8", 16mm
Drill Bits: 7/16"
Rearward
Rubber isolator
Disconnect
exhaust flange
Figure 1.
1
Qty. (4)
Carriage bolt 7/16-14 X 1.50 GR5
2
Qty. (4)
Lock washer
1.
Remove carpeting, fiber board and storage bin tray (if present) from vehicle trunk
2.
Remove the ground wire from the drivers side muffler.
3.
Disconnect the exhaust at the flange. Both sides. Keep the fasteners. Figure 1.
4.
Push exhaust toward the rear of the vehicle and off the rubber isolator. Gently push the heat shield toward the frame rail exposing the area between the frame
rail and wheel well.
5.
Raise the hitch into position (being careful not to scratch the fascia) between the frame rails and spare tire wheel well. Align the rear edge of the side bracket
on the hitch flush against the bulkhead. Check the location of the hitch on the vehicle.
6.
Using the hitch as a template mark and center punch the (2) holes on both sides.
7.
Lower hitch. Drill 7/16" hole up through bottom of trunk pan at center punched locations. Check hole alignment under vehicle and adjust if necessary.
Remove burrs.
8.
Position plate over holes inside trunk and insert the carriage bolts through plate and trunk pan (do not install over carpet).
9.
Raise hitch back into position over carriage bolts and install lock washers and hex nuts as shown. Tighten all 7/16-14 GR5 fasteners to 50 LB-FT.
10.
Gently bend heat shield back into position. Reattach the exhaust to the rubber isolator and flange. Reattach ground wire to the muffler.
11.
Apply sealant at bolt attachments inside spare tire well to prevent the intrusion of water and exhaust fumes to vehicle interior.
12.
Replace the carpeting, fiber board and storage bin tray (if present).
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2007, 2008 Cequent Towing Products
Installation Instructions
Nissan Altima
Fascia
Nissan Maxima
Drawbar Kit:
Drawbar must be used in the
RISE position only.
Bulkhead
Note:
Fasteners
same both
sides.
Tighten all 7/16 GR5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
Do Not Exceed Lower of Towing Vehicle
3594
2000 LB (908Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Wiring Access Location: PC3, PC4
1
Drilled holes 2
each side
2
3
3
Qty. (4)
Nut 7/16-14
Sheet 1 of 3
24796N
Part Numbers:
24796
60873
77168
Manufacturer's Rating or
Spare tire
wheel well
Plate
Rubber isolator
9-4-08
Form F206 Rev A 5605
Disconnected
exhaust flange
Rev. B
Publicidad
Manuales relacionados para Cequent Towing Products 24796
Resumen de contenidos para Cequent Towing Products 24796
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2007, 2008 Cequent Towing Products Sheet 1 of 3 24796N 9-4-08 Rev.
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. 2007, 2008 Cequent Towing Products Feuille 2 de 3 24796N 9-4-08 Rev.
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. 2007, 2008 Cequent Towing Products Hoja 3 de 3 24796N 9-4-08 Rev.