Pyronix XDH10TT-AM Guia De Inicio Rapido

10m Pet Immune External Detector
Environmental Class IV
9.9GHz: 10.525GHz
AT BE CH CY CZ DK FI BE CH CY DK HU IE IS
FR GR HR HU IE IS IT IT MT NL NO SE SI
LT MT NL PL SI TR
10.587GHz
GB
E N G L I S H
References
Anti-Masking: The XDH10TT-AM uses the patented Anti-Masking
technology to detect when one or both PIR detectors as well as the
Microwave module are Masked.
The detector is able to detect aluminium foil, spray and any object position
on or in front of the detector with the purpose of obstructing the field of
view of the PIR or MW sensors.
The masking area is adjustable between 0 to 1M.
If the masking area is entered the Blue LED starts flashing to show that
the area has been compromised. If the obstacle is removed after 30 seconds
and the BLUE alarm LED have activated the detector will reset to normal. If
the obstacle still remains after 1 minute, the MASK and ALARM relay will open
and the Green and Orange LEDs will be permanently activated. To reset the
detector, the obstacle must be removed and a walk test should be done.
The Anti-Masking can be disabled when the panel is armed. For this the RI
terminal has to be connected to an output of the panel which is POSITIVE
when ARMED. To enable this feature also, switches 2 and 4 must be OFF.
Blocking: This feature allows the detection of obstruction located at 10M
or less and is used when the panel is disarmed. When the blocking feature is
active the Alarm relay will open and the Green and Orange LEDs will be
activated. To reset the blocking XD should be walk tested so that both PIRs
and MW sensors are activated.
To enable the feature, switches 3 and 4 must be OFF and the RI input
should be connected to an output on the control panel which gives a
NEGATIVE when DISARMED and a POSITIVE when ARMED.
Technical Specification
Casing: 3mm polycarbonate, 0.4mm HDPE in Lens Area
Lenses: 2 x Lens 5 (UV Compensated)
Tri-Detection Method: 2 low noise dual element passive infrared sensors
and a microwave doppler unit
Tri-Masking Adjustable: from 0M to 1M. Covers all 3 technologies.
Sensitivity Selectable: AUTO or HIGH
Temperature Compensation: Digital
Detection Speed: 0.25 - 2.5m/s
Operating Voltage: 9-16VDC, 13.8VDC typically
Current Consumption: 24mA @ 13.8VDC quiescent
Relay Output: 3 x SELV limits, 60VDC 50mA (42.4VAC peak)
Mounting Height & Range: 1.8M - 2.4M = 10M (Lens 5)
Pet Immunity: 10kg
Tamper Switch: 12VDC 50mA both front and rear
Storage Temperature: -40°C to +80°C (+40°F to 176°F)
Operating Temperature: -30°C to +70°C (+22°F to 158°F)
Dimensions & Weight: 188 x 77 x 84mm, 0.3kg
Emissions EN55022 Class 2.
IP Rating: IP55
Warranty
This product is sold subject to our standard warranty conditions and is
warranted against defects in workmanship for a period of five years
(excluding lens). In the interest of continuing improvement of quality,
customer care and design, Pyronix Ltd reserves the right to amend
specifications, without prior notice.
Product Warning Information
For electrical products sold within the European Community. At the end of
the electrical products life, it should not be disposed of with household
waste. Please recycle where facilities exist. Check with your Local Authority
or retailer for recycling advice in your country.
Optional Accessories
Adjustable Lens Masks
XD-FIXEDBRACKET + Fixed Lens Mask
XD-WALLBRACKET + XD-45D-ADAPTER
Frequency
This product operates in a European non-harmonized frequency band.
Hereby, Pyronix, declares that this XDH10TT-AM is in compliance with the
essential requirements and other relevant provisions of Directive
1999/5/EC. The declaration of conformity may be consulted at
www.pyronix.com/product-compliance.php
 0845 6434 999 (UK). +44(0)1709 535 225
START
3
3EOL
3k
15k
12k
8k2
6k8
5k6
EOL EOL EOL R1 LED ALARM N/O EOL
4k7
TAMPER ALARM N/C MASK/FAULT TAMPER
2k2
1k
10k
10k
5k6
6k8
4k7
5k6
3k9
4k7
3k9 2k7
2k7 2k2
2k2 1k5
A A T T
+12V 0V 1k5 1k +12V 0V
EOL INPUT 1 COM 1k
820R
PCX 46
1M
MAX
Max: 1M
≤1m
 customer.support@pyronix.com
W = XD-WALLBRACKET
F = XD-FIXEDBRACKET
MASK/ALARM LINK
2
DEOL
N/C
3k
15k
12k
8k2
6k8
5k6
EOL EOL R1 LED ALARM N/O EOL EOL EOL R1
4k7
ALARM N/C MASK/FAULT TAMPER ALARM N/C MASK/FAULT
2k2
1k
10k
10k
5k6
6k8
4k7
5k6
3k9
4k7
3k9 2k7
2k7 2k2
2k2 1k5
A A T T A A T T
1k5 1k +12V 0V
EOL INPUT 1 COM 1k EOL INPUT 1 COM
820R
PCX 46 PCX 46
30%
30% Mask
OFF
>1m
 www.pyronix.com
2
DEOL
3k
15k
12k
8k2
6k8
5k6
LED ALARM N/O
4k7
EOL EOL EOL R1 LED ALARM N/O
2k2 TAMPER ALARM N/C MASK/FAULT
1k
10k
10k
10k
5k6
6k8
6k8
4k7
5k6
5k6
3k9
4k7
4k7
3k9 2k7 3k9
2k7 2k2 2k7
2k2
2k2 1k5
A A T T
+12V 0V 1k5
1k5 1k
EOL INPUT 1 COM 1k
1k
PCX 46 820R
820R
EOL EOL EOL R1
TAMPER ALARM N/C MASK/FAULT
+12V 0V
PCX 46
Pyronix Limited, Pyronix House, Braithwell Way, Hellaby, Rotherham, S66 8QY, UK
PCX
ATE INPUTS
OFF
N/C
3k
3k
15k
15k
12k
12k
8k2
8k2
6k8
6k8
5k6
5k6
4k7 EOL EOL EOL R1 LED ALARM N/O
4k7
TAMPER ALARM N/C MASK/FAULT
2k2
2k2
1k
1k
10k
10k 10k
5k6
5k6
6k8
4k7
5k6 4k7
3k9
3k9
4k7
2k7
3k9 2k7
2k2
2k2
2k7
1k5
2k2 1k5
1k
A A T T
+12V 0V 1k5 1k
EOL INPUT 1 COM
1k
820R
PCX 46
3k
15k
12k
8k2
6k8
5k6
4k7
2k2
1k
LED ALARM N/O
10k 10k
5k6
6k8
4k7
5k6
4k7 3k9
3k9 2k7
2k2
2k7
1k5
2k2
1k5 1k
1k
820R
No resistors are required for
the Alarm N/O relay