Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
AVENTICS | Serie MU1 | R412021819–BDL–001–AB | English
English
1
About This Documentation
These instructions contain important information for the safe and appropriate
assembly and commissioning of the product.
O Read these instructions carefully, especially the section "Notes on Safety", before
working with the product.
Additional documentation
O Read and follow the operating instructions for the MU1 series maintenance unit.
O Also follow the instructions for the other system components.
O Furthermore, observe general, statutory and other binding rules of the European
and national laws, as well as the valid regulations in your country to protect the
environment and avoid accidents.
Presentation of information
Warnings
In this document, there are warning notes before the steps whenever there is a
danger of personal injury or damage to equipment. The measures described to avoid
these hazards must be observed.
Structure of warnings
Hazard type and source
Consequences of non-observance
O Measures to avoid these hazards
Meaning of the signal words
Indicates a hazardous situation which, if not avoided, could result in minor or
moderate injuries.
Indicates damage to property: The product or its environment may be damaged.
Symbols
Operation may be impaired if this information is disregarded.
2
Notes on Safety
The product has been manufactured according to the accepted rules of current
technology. Even so, there is a risk of injury or damage if the following general safety
instructions and the specific warnings given in this instruction manual are not
observed.
O Read these instructions completely before working with the product.
O Keep these instructions in a location where they are accessible to all users at all
times.
O Always include the operating instructions when you pass the product on to third
parties.
Intended use
The product is exclusively intended for installation in a machine or system or
combination with other components to form a machine or system. The product may
only be commissioned after it has been installed in the machine/system for which it
is intended.
Use is permitted only under the operating conditions and within the performance
limits listed in the technical data. Only use compressed air as the medium.
The product is technical equipment and is intended for professional use only.
Intended use includes having completely read and understood these instructions,
especially the section "Notes on Safety".
Improper use
Improper use includes using the product
W
for any application not stated in these instructions, or
W
under operating conditions that deviate from those described in these
instructions.
Personnel qualifications
All tasks associated with the products require basic mechanical, electrical, and
pneumatic knowledge, as well as knowledge of the respective technical terms. In
order to ensure operational safety, these tasks may only be carried out by qualified
personnel or an instructed person under the direction of qualified personnel.
Qualified personnel are those who can recognize possible hazards and institute the
appropriate safety measures, due to their professional training, knowledge, and
SIGNAL WORD
CAUTION
NOTICE
experience, as well as their understanding of the relevant conditions pertaining to
the work to be done. Qualified personnel must observe the rules relevant to the
subject area.
General safety instructions
W
Observe the valid local regulations to protect the environment in the country of
use and to avoid workplace accidents.
W
Only use AVENTICS products that are in perfect working order.
W
Examine the product for obvious defects, such as cracks in the housing or
missing screws, caps, or seals.
W
The warranty will not apply if the product is incorrectly assembled.
W
Do not place any improper mechanical loads on the product under any
circumstances.
W
Product warnings and information must be legible, i.e. not covered by paint, etc.
Safety instructions related to the product and technology
W
Lay cables and lines so that they cannot be damaged and no one can trip over
them.
W
Do not operate the product in aggressive ambient air (i.e. solvent gases).
W
Dirt must not collect on or in the filters, reservoirs, or windows. Replace
reservoirs when the dirt cannot be removed from the drain (drain can clog).
3
Delivery Contents
The delivery contents include:
W
1 lubricator as per order
W
Operating instructions
4
About This Product
1
The lubricators are maintenance unit components. They are used to regulate oil
release to the compressed air. Cylinder speeds >1 m/s, metal-metal sealing valves,
and compressed air tools are typical applications.
5
Assembly, Commissioning, Operation
O Let the product acclimatize for several hours before commissioning; otherwise,
water may condense in the housing.
Danger of injury if assembled under pressure or voltage!
Assembling when under pressure or voltage can lead to injuries and damage to
the product or system components.
O Make sure that the relevant system part is not under voltage or pressure
before you assemble the product.
O Protect the system against being switched on.
System is operating under pressure.
Incorrect installation could damage the maintenance unit/device and cause
serious injury.
O Before start-up, check that all connections, ports, and maintenance devices
have been correctly installed.
Sudden surge in pressure during start-up!
If no SSU filling unit is used, the system will suddenly be under pressure during
start-up! This could cause dangerous and sudden cylinder movements.
O When starting up the system, make sure that the cylinders are in their end
position. For cylinders not in the end position, make sure they do not present
any danger.
Noxious oil mist!
If oil is used in the compressed air system, noxious oil mist may develop.
O Only operate the lubricator in closed pneumatic systems.
Assembling the W01 mounting elements
O See Figure
W01
.
2
Assembling the reservoir and protective guard
1. Slide the protective guard on the reservoir (a).
2. Place the seal (b) and the reservoir with the protective guard (c) onto the
lubricator housing.
3. Slide the locking ring (d) over the reservoir with the protective guard and tighten
firmly.
Filling the lubricator
W
Fill the reservoir with the specified oil only (see "Technical Data").
W
Regularly check the oil level and refill if the oil has reached the minimum level
indicated on the reservoir.
If the filling level is too high, oil can reach the system and damage it.
CAUTION
3
Publicidad
Tabla de contenido
