AmerTac Westek LPL704RC Manual Del Propietário

LPL704RC/LPL704WRC (4 Light Heads) Owner's Manual
Location of Controls
1. ON/OFF Switch/Remote Control Signal Receiver
2. Swiveling Light Heads
3. Battery Compartment*
4. Remote Control
5. Remote Control Signal Transmitter
6. Battery Compartment
7. ON/OFF Switch
8. Dimmer Function
9. Timer Function
*On back of unit
Installation
Note: Hook and loop tape may be cut to desired size for easier removal. Remove the mounting bracket if you are using the
hook and loop tape. To do so, hold the light with mounting bracket facing up and the power button facing you.
Slide the mounting bracket to the left and pull up to remove it.
1. Check the location of where you want to place the Track Light. Make sure it is clean and there is no debris or
dust.
2. Two sets of hook and loop tape are included. Place the two pieces of hook and loop tape together so the
hook and loop sides adhere to each other. Repeat this step for the second set of hook and loop tape.
3. Remove the plastic covering on one sticky side of the tape. Repeat this step for the second set of hook and
loop tape.
4. Place one set of the hook and loop tape in the left and right rectangular recessed areas on the base of the
Track Light.
5. Remove the plastic covering on the other sticky side of the tape. Repeat this step for the second set of hook
and loop tape.
6. Place the Track Light in the desired location. Press fi rmly for fi ve (5) seconds so the tape adheres to the
surface.
CAUTION: Be cautious of what surface the hook and loop adhesive is attached to, as it may remove paint or
damage surface.
Screws and Detachable Bracket (included)
1. Remove both pieces of hook and loop tape by pulling the tape away from the base of the light.
2. Remove the mounting bracket so that it can be used as a template for the screw holes.
To do so, hold the light with mounting bracket facing up and the power button
facing you. Slide the mounting bracket to the left and pull up to remove it.
3. Drill two (2) pilot holes in the location where you want to mount the under cabinet light. Use the detachable
bracket as a guide for the pilot holes.
4. Place screws (included) in pre-drilled holes. Do not over tighten.
5. Clip the under cabinet light to the detachable bracket by aligning and inserting the posts on the bracket into the keyhole slot
openings on the backside of the under cabinet light. Slide the light to the left to lock it into position.
6. To remove the under cabinet light from the detachable bracket, simply slide the light to the right and pull down.
Operating Directions
Light Positioning
Each of the four light heads may be positioned independently. They can be rotated 330° left or right as well as pivoted up and down for
the desired light positions.
NOTE: Each light head can only be turned 330° left or right (Fig 1). To prevent damage to the unit, do NOT overturn the light heads.
Doing so may damage the unit and will void the warranty.
YOU CAN OPERATE AND CONTROL THE TRACK LIGHT TWO WAYS:
ON/OFF Operation
1. Press once to turn light ON.
2. Press again to turn the light OFF.
Remote Operation Using the Wireless Remote Control
Where you mount the track light will determine how is best to control the track light using the remote control. The remote uses Infra Red
technology. This is the same type of technology used in most TV remote controls. As such pointing the remote directly at the track light
may be necessary. For best performance, point remote to the receiver (red lens) of light within 15 feet (5 meters) & 30 degrees directly
(unblocked).
1. Press ON/OFF to turn the fi xture on and off.
2. Use the + and - keys to dim and brighten the light
3. Use the 4 timer function buttons to select 15, 30, 45 or 60 minutes. The light will blink to accept the command and will shut-off in
the selected duration.
NOTE: It is recommended to mount the Track Light with the Remote Control Signal Receiver facing out toward the
Remote Control.
Changing the Remote Control Batteries
If the Remote Control does not work to turn the LED lights ON, this may be an indication that the battery needs to be replaced.
Replacing the Batteries:
1. Using a small phillips head screwdriver, remove the screw on the back of the Remote. As the screw is very small, take care not to
lose after removing. Remove battery compartment cover.
2. Remove the old battery (if replacing).
3. Insert new CR2025 battery. Be sure to match the battery polarity guide when installing new battery.
4. Replace the battery compartment cover and screw (making sure not to overtighten).
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: Modifi cations to this product not approved by the party responsible for compliance could void the user's authority to operate the product.
Limited Warranty
Under normal use and conditions, AmerTac provides to the original purchaser of this product a one year limited
express warranty that is set forth in the Limited Warranty stated in full at www.amertac.com/warranties. The
Limited Warranty is in lieu of all other express or implied warranties or liabilities subject to the exceptions
explained fully in the Limited Warranty on the website.
REMOTE CONTROLLED
LED UNDER CABINET LIGHT
1
5
7
8
9
4
6
Fig 1
This product contains a Button battery. If swallowed, it could cause severe injury or death in just 2
hours.
Seek medical attention immediately.
Inserting/Replacing the Batteries
If the LEDs appear to be dim this is an indication that your batteries need to be replaced.
1. Remove the mounting bracket at the back side of the Under Cabinet Light. To do so, hold the light with
mounting bracket facing up and the power button facing you. Slide the mounting bracket to the left
and pull up to remove it.
2. Slide the battery compartment covers in towards the center of the unit to open the battery
compartments.
3. Remove old batteries, if replacing batteries. Insert six new AAA batteries.
4. Make sure to follow battery polarity guide when installing new batteries.
5. Replace battery compartment housing.
Battery Precautions:
1. Use only the size and type of batteries specifi ed.
2. Always purchase the correct size and grade of battery most suitable for the intended use.
3. Be sure to follow the correct polarity when installing the batteries as indicated in the battery
compartment.
Reversed batteries may cause damage to the device.
4. Do not mix alkaline, standard (Carbon-Zinc), or rechargeable (Nickel Cadmium) batteries.
5. Replace all batteries of a set at the same time. Do not mix old and new batteries.
6. Clean the battery contacts and also those of the device prior to battery installation.
7. Do not dispose of batteries in fi re.
8. Remove batteries if consumed or if product is to be left unused for an extended period of time.
3
2
250 Boulder Dr.
Breinigsville, PA 18031
610-336-1330
www.amertac.com
Made in China / Fabriqué en
Chine / Fabricado en China
© 2018 AmerTac™
I18-0009-A