AmerTac Westek LPL704AC Manual Del Propietário

LPL704AC/LPL704WAC (4 Light Heads) Owner's Manual
Location of Controls
1. ON/OFF Switch/Remote Control Signal Receiver
2. Swiveling Light Heads
3. Battery Compartment*
4. Direct AC Power Port
5. Link Connector
6. AC Adaptor
*On back of unit
Installation
Note: Hook and loop tape may be cut to desired size for easier removal. Remove the mounting bracket if you are using the
hook and loop tape. To do so, hold the light with mounting bracket facing up and the power button facing you. Slide the
mounting bracket to the left and pull up to remove it.
1. Check the location of where you want to place the Track Light. Make sure it is clean and there is no debris or dust.
2. Two sets of hook and loop tape are included. Place the two pieces of hook and loop tape together so the hook and
loop sides adhere to each other. Repeat this step for the second set of hook and loop tape.
3. Remove the plastic covering on one sticky side of the tape. Repeat this step for the second set of hook and loop tape.
4. Place one set of the hook and loop tape in the left and right rectangular recessed areas on the base of the Track Light.
5. Remove the plastic covering on the other sticky side of the tape. Repeat this step for the second set of hook and loop
tape.
6. Place the Track Light in the desired location. Press fi rmly for fi ve (5) seconds so the tape adheres to the surface.
CAUTION: Be cautious of what surface the hook and loop adhesive is attached to, as it may remove paint or damage
surface.
Screws and Detachable Bracket (included)
1. Remove both pieces of hook and loop tape by pulling the tape away from the base of the light.
2. Remove the mounting bracket so that it can be used as a template for the screw holes.
To do so, hold the light with mounting bracket facing up and the power button
facing you. Slide the mounting bracket to the left and pull up to remove it.
3. Drill two (2) pilot holes in the location where you want to mount the under cabinet light. Use the detachable bracket as
a guide for the pilot holes.
4. Place screws (included) in pre-drilled holes. Do not over tighten.
5. Clip the under cabinet light to the detachable bracket by aligning and inserting the posts on the bracket into the
keyhole slot openings on the backside of the under cabinet light. Slide the light to the left to lock it into position.
6. To remove the under cabinet light from the detachable bracket, simply slide the light to the right and pull down.
Operating Directions
Light Positioning
Each of the four light heads may be positioned independently. They can be rotated 330° left or right as well as pivoted up and
down for the desired light positions.
NOTE: Each light head can only be turned 330° left or right (Fig 1). To prevent damage to the unit, do NOT overturn the
light heads. Doing so may damage the unit and will void the warranty.
Inserting/Replacing the Batteries
If the LEDs appear to be dim this is an indication that your batteries need to be replaced.
1. Remove the mounting bracket at the back side of the Under Cabinet Light. To do so, hold the light with mounting
bracket facing up and the power button facing you. Slide the mounting bracket to the left and pull up to remove it.
2. Slide the battery compartment covers in towards the center of the unit to open the battery compartments.
3. Remove old batteries, if replacing batteries. Insert six new AAA batteries.
4. Make sure to follow battery polarity guide when installing new batteries.
5. Replace battery compartment housing.
NOTE: This unit is designed to operate using either 6 AAA or 3 AAA batteries. When using only 3 AAA batteries, be sure
to place all three batteries in one battery compartment. The unit's output/brightness will be the same whether using 6 AAA
or 3 AAA batteries.
However, the run time from 3 AAA batteries will be less.
Battery Precautions:
1. Use only the size and type of batteries specifi ed.
2. Always purchase the correct size and grade of battery most suitable for the intended use.
3. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment.
Reversed batteries may cause damage to the device.
4. Do not mix alkaline, standard (Carbon-Zinc), or rechargeable (Nickel Cadmium) batteries.
5. Replace all batteries of a set at the same time. Do not mix old and new batteries.
6. Clean the battery contacts and also those of the device prior to battery installation.
7. Do not dispose of batteries in fi re.
8. Remove batteries if consumed or if product is to be left unused for an extended period of time.
Operation from Direct AC Power (120V)
No batteries? Easy access to AC power? Use the AC adaptor included with this unit to power the light from direct
household current (120V).
Important Notes regarding using AC adaptor:
• There are 2 power ports on each light unit. Only one port is for use with the AC
adaptor. This input port is marked with the words "DC IN 5V" (see Fig. 1).
• The LED indicator positioned next to Input port will illuminate red when the unit is operating from direct AC power.
• Only use the AC adaptor provided with this unit to power the unit. Using a different
AC adaptor may damage the unit and will void the warranty.
Powering More than One Light Using Only One AC Adaptor
These lights are designed with a unique Link Connect circuit that allows you to power two lights using only one AC adaptor
(in the event you purchase more than one of our Model LPL704W-AC lights).
The Link Connect cord (included) has an input plug on either end. Follow the below listed instructions for linking two units.
Step 1: Plug AC adaptor into Input Port marked "DC IN 5V" on one light unit (we will call this Unit 1).
Step 2: Plug input plug from Link Connect cord to port marked "DC OUT 5V" on Light Unit 1.
Step 3: Plug the other input plug end from Link Connect cord to port marked "DC IN 5V" on Light Unit 2.
NOTE: You can only connect and power two units from one AC adaptor supplied.
Attempting to link more than two units may damage the lights and/or the AC adaptor and will void the warranty.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: Modifi cations to this product not approved by the party responsible for compliance could void the user's authority to operate the product.
Limited Warranty
Under normal use and conditions, AmerTac provides to the original purchaser of this product a one year limited express
warranty that is set forth in the Limited Warranty stated in full at www.amertac.com/warranties. The Limited Warranty
is in lieu of all other express or implied warranties or liabilities subject to the exceptions explained fully in the Limited
Warranty on the website.
LED UNDER CABINET LIGHT
6
Fig. 1
Fig 1
Battery Compartment
Housing
1 1
2
3
5
Direct AC Power Port
ON/OFF/Dimmer Switch
Battery Compartment
Housing
©2019 AmerTac™
250 Boulder Drive
Breinigsville, PA 18031
www.amertac.com
Made in China / Fabriqué en Chine /
Hecho en China
4
I19-0001-A