Troubleshooting Guide - Sylvania SRT2213B Manual Del Usuario

OPERATIONS (Continued)
4) Press the CH(annel) ▲
B TV RATING
or ▼ button to point to
MPAA RATING
CHANGE CODE
"TV RATING".
Then, press the
VOL(ume) ▲ button.
5) Press the CH(annel) ▲
or ▼ button to point to
B TV-Y [VIEW]
TV-Y7( ) [VIEW]
your desired item.
TV-G [VIEW]
Then, press the TV-PG( ) [VIEW]
TV-14( ) [VIEW]
VOL(ume) ▲ button
TV-MA( ) [VIEW]
to select [BLOCK] or
[VIEW].
<Selection> <Rating Category
Explanations>
• TV-Y: Appropriate for all children
• TV-Y7: Appropriate for children seven and
older
• TV-G: General Audience
• TV-PG: Parental Guidance suggested.
• TV-14: Unsuitable for children under 14
• TV-MA: Mature audience only
When you select the rating category and turn
●
it [BLOCK], the higher rating will turn
[BLOCK] automatically. Also, the lower rat-
ing will turn [VIEW] automatically.
When you turn "TV-Y" to [BLOCK] or
●
[VIEW], then all ratings will turn to
[BLOCK] or [VIEW] automatically.
When you turn "TV-MA" to [VIEW], then
●
all ratings will turn to [VIEW] automatical-
ly.
6) Press the MENU button to exit the menu.
[V-CHIP SET UP SUB RATINGS]
When you select TV-Y7, TV-PG, TV-14, or
TV-MA and you press the VOL(ume) ▲ but-
ton, the sub-ratings will appear on the TV
screen.
If you select the rating category (example: TV-
PG) and turn it [BLOCK] or [VIEW], the sub-
ratings (example: V for Violence) will turn
[BLOCK] or [VIEW] automatically.
You can set the sub-ratings to [BLOCK] or
[VIEW] individually when the rating category
is set to [BLOCK]. To set the sub-ratings indi-
vidually, follow the steps below.

TROUBLESHOOTING GUIDE

Sometimes a performance problem can be easily solved by checking seemingly apparent but often over-
looked possibilities. Before arranging for service, check these items. It could save you time and money.
QUICK SERVICE CHECK LIST
POSSIBLE REMEDY
Try a new channel, if OK, then possible station trouble.
Is TV plugged in?
Power at outlet?
Is TV's POWER button on?
Is antenna connected to terminal on the back of the set?
If outside antenna is being used, check for broken wire.
Check for local interference.
Turn off with POWER button and then turn it on after about a minute.
Adjust COLOR control.
Adjust CONTRAST & BRIGHT control.
Check batteries in Remote Control.
Move the TV away from the nearby appliances which have Magnetism.
Unplug the TV power cord, then plug it in again 30 minutes or so later.
Closed Caption Problem
My TV is showing captions that are You are watching a live broadcast and spelling errors made by the
misspelled. closed captioning production company may pass through uncorrect-
ed. A prerecorded program will not show any misspelled words
because of the normal time available for editing the captions.
My TV will not show the text in its entirety Captions that are delayed a few seconds behind the actual dialogue
or there is a delay of what is being said. are common for live broadcasts. Most captioning production compa-
nies can display a dialogue to a maximum of 220 words per minute.
If a dialogue exceeds that rate, selective editing is used to insure that
the captions remain up-to-date with the current TV screen dialogue.
My captions are scrambled with white Interference caused by building, power lines, thunderstorms, etc.
boxes on the TV screen. may cause scrambled or incomplete captions to appear.
My program guide listed a TV show as Broadcasters may at times use a time compression process to the
being closed captioned actual program so that additional advertising time can be given.
but none of the captions were displayed. Since the decoder cannot read the compressed information, captions
will be lost.
My prerecorded videotape does not show The videotape was either an illegal copying or the tape duplicating
any captions. The tape box mentions it company accidentally left out the captioning signals during the
being closed captioned. copying process.
My TV screen shows a black box on certain You are in the TEXT mode. Select CAPTION mode or CAPTION
channels. [OFF].
All manuals and user guides at all-guides.com
When you select [TV-Y7]:
●
Press the CH(annel) ▲
or ▼ button to select
TV-Y7 [BLOCK]
"FV" (Fantasy
Violence). Then, press
FV [BLOCK]
the VOL(ume) ▲ but-
ton to select [BLOCK]
or [VIEW].
When you select [TV-PG], [TV-14] or
●
[TV-MA]:
Press the CH(annel) ▲
TV-PG [BLOCK]
or ▼ button to select
D [BLOCK]
"D" (Suggestive
L [BLOCK]
Dialog), "L"(Coarse
S [BLOCK]
V [BLOCK]
Language), "S"(Sexual
Situation), or "V"
(Violence). Then, press
the VOL(ume) ▲ but-
TV-Y [VIEW]
TV-Y7 ( ) [VIEW]
ton to select [BLOCK]
TV-G [BLOCK]
or [VIEW].
TV-PG (DLSV) [BLOCK]
TV-14 (DLSV) [BLOCK]
Note: When you select
TV-MA ( LSV) [BLOCK]
[TV-MA], "D" does not
appear on the TV screen.
The sub-ratings which set to [BLOCK]
●
appear next to the rating category in the TV
RATING menu.
Possible Remedy
[V-CHIP ACCESS CODE]
To change access code, follow steps.
1) Press the MENU button, then press the
CH(annel) ▲ or ▼
PICTURE
button to select V-
CHANNEL SET
[ENGLISH] ESPAÑOL
CHIP SET UP. Press
B V-CHIP SET UP
the VOL(ume) ▲ but-
CAPTION [OFF]
ton to continue.
2) Press the number buttons to enter your old
access code. If you
have never set up your
ACCESS CODE
personal access code,
- - - -
use 0000.
3) Press the CH(annel) ▲
or ▼ button to select
CHANGE CODE.
Then, press the
TV RATING
MPAA RATING
VOL(ume) ▲ button
B CHANGE CODE
to continue.
4) Use the number but-
tons to enter your
desired access code in the NEW CODE
space. Then, enter the
NEW CODE
same code in the
- - - -
CONFIRM CODE
CONFIRM CODE
space. Your new access - - - -
code is set. You will
return to the "V-CHIP SET UP".
If the code in the CONFIRM CODE space
does not match the code in the NEW CODE
space, repeat step 4, making sure you enter the
same new code exactly in the CONFIRM
CODE space.
MAINTENANCE
CABINET CLEANING
Wipe the front panel and other exterior sur-
●
faces of the TV with a soft cloth immersed
in lukewarm water and wrung dry.
Never use a solvent or alcohol. Do not spray
●
insecticide liquid near the TV. Such chemi-
cals may cause damage and discoloration to
the exposed surfaces.
PICTURE TUBE CLEANING
Wipe the picture tube of the TV with a soft
cloth. Before cleaning the picture tube, discon-
nect the power cord.
SPECIFICATIONS
GENERAL SPECIFICATIONS
Television system: NTSC-M
TV Standard
Closed Caption
System: §15.119/FCC
Channel coverage
VHF: 2 ~ 13
UHF: 14 ~ 69
CATV: 2 ~ 13, A ~ W,
W+1 ~ W+84,
A-5 ~ A-1, 5A
Tuning System 181 channel
frequency synthesized
tuning system
Channel access: Direct access keyboard,
programmable
scan and up/down
Terminals
Antenna input: VHF/UHF/CATV
75 ohm unbalanced
(F-type)
Video input: RCA connector x 1
Audio input: RCA connector x 1
Earphone: 1/8" monaural (3.5mm)
ELECTRICAL SPECIFICATIONS
Sound output: 1W, 8 ohm
NOTES:
• If a power failure occurs, the default code,
0000, will be the active access code again.
• If you connect the power cord to an AC out-
let that is controlled by a wall switch, your
personal access code will be erased every
time you turn off the power at the wall
switch. The default code will be the active
code again.
[IF YOU FORGET YOUR ACCESS CODE]
You should restore the access code to default
code, 0000. To restore 0000 as your personal
access code, unplug the TV's power cord for
10 seconds, then plug it in again.
SUPPLIED
ACCESSORIES
Remote control unit
(N0138UD or N0139UD)
Batteries ("AA" x 2)
Rod Antenna
[13" model only]
(0EMN00673 or
0EMN01599)
Owner's
Owner's Manual Manual
OTHER SPECIFICATIONS
Remote control: Digital encoded
infrared light system
Operating
temperature: 5°C to 40°C
(41°F~104°F)
Power requirements: AC120V, 60Hz
[ 13" model ]
Power consumption
(Maximum): 53W
Picture tube: 13"
Dimensions: H : 12-3/4"(323mm)
W: 14-1/8"(358mm)
D : 14-4/9"(367mm)
Weight: 19.0 lbs. (8.5kg)
[ 19" model ]
Power consumption
(Maximum): 72W
Picture tube: 19"
Dimensions: H : 16-3/4"(428mm)
W: 18-3/4"(475mm)
D : 18" (454mm)
Weight: 37.5 lbs. (17kg)
•Designs and specifications are subject to
change without notice and without our
legal obligation.
•If there is a discrepancy between languages,
the default language will be English.