Asist AE9CPV30-10A Instrucciones De Uso página 41

Additional safety instructions
Before use, read these safety instructions and keep
them for future reference. ! - This symbol identifi es
risks of injury or damages to the equipment. ! Should
you not observe the instructions stated in this manual,
risk of injury arises. ! The electric submersible sludge
pump complies with applicable technical regulations
and standards. The device is designated to pump fresh
water from wells, shafts and other water reservoirs or
to operate irrigation devices and systems. Must not be
used for distribution of potable water or food transport.
Explosive, fl ammable, aggressive or harmful materi-
als as well as excrements must not be pumped. The
device is not suitable for interrupted operations (e.g.
uninterrupted circulate running in fi ltering devices). In
addition, it is not suitable for fl uids with abrasive ma-
terials (e.g. sand) or added impurities, sand, sludge or
soil. ! Protect the device from freezing.
• Protect the product from children playing with it.
• Always respect applicable both national and interna-
tional safety, health and operating regulations.
• The device should be connected only to the socked
with properly installed protective pin.
• Before connecting the device, you must double check
that the power socket corresponds with the values to
plug the device.
• The device may be used only in scope of limits de-
fi ned for the voltage, output and rotations (see type
label).
• Do not touch the power plug with wet hands! When
unplugging from the socket, always hold the connec-
tor, never the cord.
• Do not fold, squeeze, pull or run over the cord, pro-
tect it from sharp edges, oil and heat.
• Do not lift up the device using the cord nor use the
cord forany other purposes.
• Check the plug and cord before every use.
• When the power cord is damaged, disconnect the
plug immediately. Never use the device
with damaged power cord.
• If the device is not in operation, the power plug must
be always disconnected.
• Before connecting the power plug, make sure the de-
vice is turned off.
• Before disconnecting the power plug, always turn the
device off.
• When transporting the device, the power must be
disconnected.
• No extension cords may be used.
Protection against electric current
! If the device is used close to a pool, garden lake or
similar water reservoirs, you have to install an addi-
tional switch to protect from electric current accident.
Keep this switchin operating condition to guarantee
the device safety and reliability. ! The electrician re-
sponsible for the assembly must checkthat the electric
connection and the earthingclip arein accordance with
electrotechnicalregulations. ! This device may be used
only when connected into an electric circuit with re-
sidual current device 30 mA. ! The device has a power
cable with plug equipped with protective pin. The elec-
tric socket must be earthed. The faults caused by the
short circuit of the power supply are not covered by
the warranty!
KEEP THESE SAFETY INSTRUCTIONS
FOR FUTURE REFERENCE!!!
Description
1. power cord
2. pressure connection
3. suspensory lugs
4. pump body
5. suction holes
PICTOGRAMS
pictograms stated on the product packaging:
a) power supply values
b) power
c) Ip protection level
d) Maximum element size
e) Maximum liquid temperature
f) Maximum fl ow
g) Maximum delivery height
h) Maximum sink depth
Use and operation
The devices and tools ASIST Smart Garden are de-
signed only for home or do-it-yourself use. The man-
ufacturer and the importer do not recommend using
this equipment under extreme conditions and at high
loads. Any other additional requirements must be
agreed upon by the manufacturer and the buyer.
Danger of device damage!
Do not lift up the pump using the cord or the pressure
connection, because neither the cord nor the pressure
connection is dimensioned for pulling with the pump
weight load. Before putting into operation for the fi rst
time, attach a rope that is long enough to suspension
lugs. Use ropes with a suffi cient load capacity, re-
sistant to water and UV rays. Check the rope condition
regularly.
Submersible pumps are used especially for exsiccat-
ing after fl ooding, transferring liquids, pumping water
from well, but also for closed water circulation for a lim-
ited time period. - The pump can be sunk into a liquid to
the maximum depth 7 m. - Liquid that can be pumped
with the submersible pump: pure water (maximum size
of organic elements 1 mm). Caustics, fl ammable or
slightly explosive materials (e.g. petrol, diesel oil, nitro
glycerine etc.) must not be pumped or pumped over
with this pump. - The temperature of pumped liquid
41
f h
g