Initial Operation; Using The Device - BOMANN DR 906 CB Instrucciones De Servicio

Initial Operation

Fill in Water
NOTE:
• The maximum filling capacity is 600 ml. Use the measur-
ing cup provided.
• Recommendation: Use distilled water to prevent calcifica-
tion.
CAUTION:
Do not use battery water, water from tumble dryers or water
with additives such as cleaning agents, alcohol, fabric
softener or other chemicals. They could cause hazards or
damage to the appliance.
WARNING: Risk of injury!
1. Disconnect the mains plug from the wall socket.
2. Only open the appliance after the pressure has been
released. Press the steam button to do so.
3. If the appliance is still warm, wait approx. 5 minutes until
removing the lid.
4. Unscrew the lid anticlockwise to remove it.
NOTE:
For your safety, the lock features a trip-free mechanism.
If the pressure in the boiler is still too high, the lock can-
not be opened.
5. Pour any remaining water from the boiler in order to avoid
overfilling.
6. Use the funnel to fill the boiler with a maximum of 600 ml of
water.
7. Attach the lid again by turning it clockwise.
Installation of accessories
• You have the option of attaching the individual nozzles
directly onto the handle. Insert the accessory onto the
handle until the button (7) clicks into place. To release the
accessory, press the button (7) on the handle.
• The extension pipes enable you to work in large or high ar-
eas. Insert them into each other until the button on the pipe
clicks into place. Attach the pipe to the handle as described
above. To separate the pipes, press the button on the pipe
again.
• Attach the adapter (11) to the floor
brush. Insert the adapter into the
floor brush (see fig. A). Then turn
the adapter upwards by 180°.
• In order to clean sensitive floor
surfaces, use the fleece cloth. To
do so, center the floor brush on
the fleece cloth. Press the levers (12a) and clamp the
edges of the fleece cloth under the levers.
• Use the round brush for cleaning gaps, instruments, or
spaces that are hard to reach. Attach the round brush to
28
All manuals and user guides at all-guides.com
Electrical Connection
1. Before inserting the plug into the socket. Make sure that
2. Lock the steam button. To do so, press the red LOCK
3. Connect the device to a duly installed protective contact
Before you begin cleaning you should test the materials to
be cleaned as to their suitability for cleaning with steam. Do
not hold the steam nozzle for too long and too close in one
position.
1. To switch on the appliance, set the on/off switch to position I.
2. Pressure starts building up in the boiler after approx.
3. Press the red UNLOCK interlock next to the steam button.
4. Press the steam button to generate steam.
•
•
Filling the Water Tank during Operation
No steam will be discharged if the water tank is empty. The
water has to be filled up as follows:
1. To switch off the appliance, set the on/off switch to position
2. Remove the mains plug from the socket!
3. Fill fresh water into the tank as described in the chapter "Fill
4. Connect the plug to the socket again and switch the appli-
When you have finished using the device
1. To switch off the appliance, set the on/off switch to position
2. Remove the mains plug from the socket!
3. Let the unit cool down completely.
4. Empty the water tank.
the jet nozzle attachment. Lock
the round brush with a slight turn.
The snap tabs on the jet nozzle
attachment must be visible
through the holes of the round
brush (see fig. B).
the mains voltage to be used matches that of the device.
You can find this information on the nameplate.
interlock next to the steam button.
socket.

Using the Device

CAUTION:
6 minutes.
NOTE:
After a long period of non-use, it is normal that a small
amount of condensation, which has formed in the pipe,
will leak out at first.
Using the appliance with the maximum water amount
and in continuous operation will allow for steam genera-
tion of up to 15 minutes.
O.
in Water" (steps 1-7).
ance on to continue operation.
O.