Descargar Imprimir esta página

Technical Data - Proxxon MICROMOT 40 Manual De Instrucciones

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 7
0
Dear customer,
Please read the enclosed safety regulations
and operating instructions carefully before
using the unit.
Safety regulations
Attention!
Please read and apply the following safety
regulations carefully before using the machine,
thereby protecting yourself and others.
not use electrical tools in rain, under wet
O
conditions or in the vicinity of inffammable
liquids or gases.
pipes, radiators cookers and refrigerators.
conditions.
the resch of children.
not overload the machine.
O
not use weak tools for heavy duty werk.
O
not carry the machine by the power
O
sharp edges and only have it replaced by a
machine is not in use, when changing tools
the manufacturer.
- 6 -
All manuals and user guides at all-guides.com
Drilling and milling machine
Overview
Legend
1.
ON - OFF switch with Speed control
(MM 40/E only)
2 . H o o k
3. Power cable
4.
ON - OFF switch (MM 40 only)
5 . Locking p i n
6.
Spigot nut with steel clamping jaw
7.
20 mm fitting for mounting in drill stand
Description of machine
The PROXXON drilling and milling machine
MICROMOT 40 (E) is the ideal tool for precise
rust removal, engraving, chasing and cutting.
For hobby electronics, model making,
precision mechanics, jewellery shops,
opticians, arts, tool and mould making.
For marking tools and cameras.
lt tan be used on steel, non-ferrous metals,
The drill spindle is supported in a precision
ball bearing which eliminates any play.
pen-type grip.
The machine is reliably driven by a high torque

Technical data

Length:
approx. 220 mm
Weight:
approx. 230 g
Spindle collar:
Motor:
Speed (40):
20 000 rpm
Speed (40/E):
5000 to 20 000 rpm
Voltage:
Power consumption:
approx. 40 W
Noise level:
Accessories:
Drill chuck for Micromot machines
Power unit NG 2 (S/E) or NG 5 (E)
Drill stand MBS 140
Universal holder UH 34
Operation
Clamping, changing tools
Atten tionl
Disconnect mains plug before changing tools.
Never press the locking knob (arrow Fig. 2)
while the machine is running.
1
1. Turn the spigot nut
(Fig. 2) gently while
pressing the locking knob until it engages.
2. Open the clamping jaw and Change the
Clamp all tools as short as possible. Shafts,
the machine to vibrate.
Power supply
Use only power units with a minimum power
output of 1 A. We recommend use of the
PROXXON power units NG 2 (SE) or NG 5 (E).
1. Push the non-reversible plug into the power
unit.
If overloaded, the PROXXON power unit will
plug and let the power unit cool down for a
few minutes.
Working with the machine
Always wear goggles.
D
not use any broken grinding discs or bent
O
1
2. Switch the machine on
set the correct Speed (40/E only) with the
button 1.
Note:
Pressing hard does not achieve good results
when grinding. Use the correct speed and
maintain it.
Big tools pins
3. Fig. 3 Shows two typical methods for
holding MICROMOT 40. When working,
ensure that the tool is held firmly in Order
to guide the rotating application tool in a
the ventillation Slots.
4. If the unit overheats, switch it off and
a
few minutes.
The electronie Speed regulation works only
with non-stabilized power units (e. g. all
PROXXON power units). If connected to a
EC declaration of conformity
with the following EC guidelines:
EC EMC Guideline 89L336
l
EC Machine Guicleline 89/392
l
Dipl. Ing. Martin Faßbender
PROXXON S.A.
Equipment Safety Dept.
- 7 -

Publicidad

loading

Este manual también es adecuado para:

Micromot 40 e