Explanation Of Symbols; Declaration Of Ec Conformity; General Safety - Silverline 261123 Manual De Instrucciones

GB

Explanation of Symbols

• Wear breathing protection
• Wear eye protection
• Wear hearing protection
• Wear gloves
• Do not dispose of WEEE (Waste Electrical
and Electronic Equipment) as unsorted waste
• Class II construction (double insulated)
Specification
Voltage .................................................230V
Frequency ............................................50Hz
Power ...................................................1600W
No load speed ......................................660m/min
Bar length ............................................405mm
Blade type ............................................3/8" oregon
Weighted vibration ...............................5.71m/s
Sound pressure ....................................98dB(A)
Sound power ........................................112dB(A)
Double insulated ..................................
As part of our ongoing product development, specifications
of Silverline products may alter without notice.

Declaration of EC Conformity

261123
Product number:
1600W Electric Chainsaw PR 1600-EC
Description:
Silverline Tools Ltd declares that the above product conforms
to the following directive(s):
93/68/EEC, 98/37/EC
With reference to:
EN60745-1:2003+A1:2003
EN60745-2-3:2004
EN50144-1:1998+A1:2002+A2:2003
EN50144-2-3:2002+A1:2002+A2:2003
EN55014-1:2000/+A1:2001/+A2:2002
EN55014-2:1997/+A1:2001
EN61000-3-2:2000
EN61000-3-3:1995/+A1:2001
Philip Ellis
Director
Silverline Tools Ltd
Boundary Way
Lufton Trading Estate
Yeovil, Somerset
BA22 8HZ, UK
4
All manuals and user guides at all-guides.com
2

General Safety

Carefully read and understand this manual and any label attached to
the tool before use. Keep these instructions with the product for future
reference. Ensure all persons who use this product are fully acquainted
with this manual.
Even when used as prescribed it is not possible to eliminate all residual risk
factors. Use with caution. If you are at all unsure of the correct and safe
manner in which to use this tool, do not attempt to use it.
Keep guards in position
• Always keep guards in position, in good working order, correctly adjusted
and aligned. Never attempt to use a tool if any of the supplied guards are
missing. If any guards are damaged, replace before use.
Remove adjusting keys
• Always check to see that keys and adjusting devices are removed from
the tool before use.
Clean the work area
• Accidents can occur where benches and work areas are cluttered or
dirty, floors must be kept clear, avoid working where the floor is slippery.
If working outdoors, make yourself aware of all potential slip and trip
hazards before using this tool.
Children and pets
• Children and pets should always be kept at a safe distance from your
work area. Lock tools away where children can't get access to them. Do
not allow children, or untrained persons to use this tool.
Use the correct tool
• Don't force, or attempt to use a tool for a purpose it was not designed for.
• This tool is not intended for industrial use
Wear suitable clothing and footwear
• Don't wear loose fitting clothing, neckties, jewellery, or other items which
may become caught. Wear non slip footwear, or footwear with protective
toe caps where appropriate. Long hair should be covered or tied back.
Keep your balance
• Don't over reach, keep proper footing at all times, do not use tools when
standing on an unstable surface.
Accessories
• The use of any attachment or accessory other than those mentioned
in this manual could result in damage or injury. The use of improper
accessories could be dangerous, and may invalidate your warranty.
Never stand on your tool
• Standing on your tool or its stand could cause serious injury if the tool is
tipped, or collapses. Do not store materials above or near the tool so that
it is necessary to stand on the tool or its stand to reach them.
Secure work
• Where possible, always secure work. If appropriate use a clamp or vice, it
will allow you to use both hands to operate your tool.
Check for damaged or missing parts
• Before each use, check if any part of the tool is damaged or missing,
check carefully that it will operate properly and perform its intended
function. Check alignment of moving parts for binding. Any guard or other
part that is damaged should be immediately repaired or replaced by an
authorised service centre. Do not use if defective.