Black and Decker PPRH5B Manual De Instruccion página 10

Periodically check the unit's battery status on the LCD screen. Four solid bars
in the battery icon indicates a full battery. When the battery level is nearly
empty with only one solid bar, the unit MUST be recharged at this time or the
unit's built-in low voltage protection will activate. The unit will sound a beep
5 times, then the USB Charging Port will automatically turn off. The unit will
then display the battery status and voltage indicator for 10 seconds before
automatic shut down.
Note:
This unit's USB power port does not support data communication. It only
provides 5V DC/1000mA power to an external USB-powered device.
PORTABLE COMPRESSOR
The built-in 12 volt DC compressor is the ultimate compressor for all vehicle
tires, trailer tires and recreational inflatables. A nozzle adaptor is supplied
that screws onto the end of the Sure Fit
compressor hose. The compressor hose with tire fitting is stored in the storage
compartment. Refer to the "Features" illustration for locations of compressor
hose. The Compressor Power Button and Increase (+) and Decrease (–)
Compressor Pressure Control Buttons are located on the control panel on the
front of the unit.
Before proceeding, check the unit's battery status on the LCD screen. Four
solid bars in the battery icon indicates a full battery. When the battery level is
nearly empty with only one solid bar, the unit MUST be recharged before use
or the unit's built-in low voltage protection will activate. The empty Battery
Status Icon will flash for a short period of time before automatic shut down.
The compressor is capable of inflating up to 120 pounds per square inch (psi)
pressure. The compressor can operate long enough to fill up to 3 average
sized tires before the battery must be recharged. Return hose to the storage
compartment after use.
IMPORTANT: Make sure the Jump Starter Power Button has been turned off
before attempting to use the unit as a Compressor.
WARNING –
TO REDUCE THE RISK OF SERIOUS INJURY OR PROPERTY
DAMAGE: Follow all safety instructions found in the "Specific Safety
Instructions for Compressors" section of this instruction manual.
CAUTION –
TO REDUCE THE RISK OF SERIOUS INJURY OR PROPERTY
DAMAGE: When the compressor is operated at a low PSI, the unit may start
slowly and gradually rev up. When the compressor is operated at higher
PSIs, the unit may operate normally for several minutes, then rev down for
a few minutes before returning to normal operation. This feature protects
the unit from overheating during normal use. In any event, do not operate
compressor continuously for longer than 10 minutes, as it may overheat. This
could damage the compressor. If the compressor must be operated for longer
periods: every 10 minutes press the Compressor Power Button to turn the
compressor off, then restart after a cooling down period of approximately 30
minutes.
Inflating Tires or Products With Valve Stems
1. Screw the Sure Fit nozzle onto the valve stem. Do not overtighten.
®
2. Press the Compressor Power Button. A beep will sound and the backlit
LCD screen will display the following:
The Compressor Icon will light and the digital display will alternately
show the flashing pre-set PSI value (that was last set by the compressor
pressure control buttons) and the current pressure of the item being
inflated (which will light solid).
3. Press the "+" and "–" Pressure Control Buttons to set the desired
pressure from a range pre-set values (between 1 and 120), which will
display on the backlit LCD screen. The unit will sound a beep with
each press of the buttons (holding the button speeds up the upward or
downward value selection). Once the desired pressure has been entered,
release the button and the flashing digital display will show the new
selected pressure, as follows:
4. Press the Compressor Power Button once more to begin inflating. The
Compressor Icon will flash and the digital display will only show the
nozzle at the free end of the
®
current pressure value (which will light solid) to indicate the compressor
is activated. Monitor the pressure on the LCD screen.
IMPORTANT NOTE: To interrupt during inflation, press the Compressor
Power Button again.
5. When desired pre-set pressure is reached, the compressor will
automatically stop.
6. Press the Compressor Power Button again to turn off the unit.
7. Unscrew and remove the Sure Fit
8. Allow the unit to cool, then recharge before storing away.
9. Store the compressor hose and Sure Fit
Inflating Other Inflatables Without Valve Stems
Inflation of other items requires use of the nozzle adapter.
1. Screw the nozzle adapter into the Sure Fit
2. Insert the nozzle adapter into item to be inflated.
3. Follow steps 2 through 4 of the "Inflating Tires or Products With Valve
Stems" section.
IMPORTANT: Small items such as volleyballs, footballs, etc. inflate very
rapidly. Keep this in mind when setting pressure. Take extra care not to
over-inflate.
4. When the desired pressure is reached, the compressor will automatically
stop. Press the Compressor Power Button again to turn off the unit.
5. Disconnect the adapter from the inflated item.
6. Unscrew and remove the nozzle adapter from the Sure Fit
7. Allow the unit to cool, then recharge before storing away.
8. Store the compressor hose, Sure Fit
storage compartment.
CARE AND MAINTENANCE
All batteries lose energy from self-discharge over time and more rapidly at
higher temperatures. When the unit is not in use, we recommend that the
battery is charged at least every 30 days.
Never submerge the unit in water. If the unit gets dirty, gently clean the outer
surfaces of the unit with a soft cloth.
There are no user-replaceable parts. Periodically inspect the condition
of adapters, connectors and wires. Contact manufacturer to replace any
components that have become worn or broken.
Battery replacement/disposal
BATTERY REPLACEMENT
The battery should last the service life of the unit. Service life is dependent on
a number of factors including but not limited to the number of recharge cycles,
and proper care and maintenance of the battery by the end user. Contact
manufacturer for any information you may need.
SAFE BATTERY DISPOSAL
Contains a maintenance-free, sealed, non-spillable, lead acid
battery, which must be disposed of properly. Recycling is
required. Failure to comply with local, state and federal
regulations can result in fines, or imprisonment.
Please recycle.
WARNINGS
:
• Do not dispose of the battery in fire as this may result in
an explosion.
• Before disposing of the battery, protect exposed terminals
with heavy-duty electrical tape to prevent shorting (shorting can result in
injury or fire).
• Do not expose battery to fire or intense heat as it may explode.
TROUBLESHOOTING
Unit will not charge
10
nozzle from the valve stem.
®
nozzle in storage compartment.
®
nozzle. Do not overtighten.
®
®
nozzle and nozzle adapter in the
®
• Make sure the AC/USB power button has
been pressed to turn the inverter on.
• Make sure a suitable gauge extension cord
is properly connected to both the unit and a
functioning AC outlet.
nozzle.