Cleaning And Maintenance - Adler europe AD 7323 Manual De Uso

injury or damage to the device
DETAILED SAFETY INSTRUCTIONS
1.Use only original assembly parts, which were supplied with the fan set.
2.The device may be turned on only after it is fully assembled. A partially assembled and started-up device does not guarantee safe use
and proper operation.
CAUTION: DO NOT TURN THE FAN ON WITHOUT ATTACHING THE FRONT AND REAR GUARDS.
3.Place the fan away from curtains, sheer curtains and other items, which can be sucked in by the running fan.
4.Do not insert any objects into the fan grid. This could hurt your body or damage the device.
PRODUCT DEACRIOTION STAND FAN AD7323
1.Front grid
5.Speed control buttons
9.Round base
ASSEMBLING
1.Draw the adjustable pipe (6A) out of the metal pipe (6B) then fasten the nut by clockwise.
2.Assemble the pipe (6A+6B) to the base (9) with the screws.
3.Slide the base cover (7)down onto the base (9).
4.Assemble the motor unit (4) on the top of the adjustable pipe (6A) then lock it with the screw.
5.Remove the nuts from the motor shaft (10).
6.Assemble the rear grid (3) onto the motor unit (4). Rear grid (3) should fit into pins on the fan motor housing (4).
7.Thread the grid nut onto motor housing (4) to lock the rear grid (3) in place.
8.Place the propeller (2) onto motor shaft (10). Notice the pin on motor shaft should fit into slots of fan propeller.
9.Thread the propeller's cap onto threaded end of motor shaft (10).
10.Use the screws and nuts to assembly the round logo plate with the front grid (1).
11.Attach front grid (1) to rear grid (3). Then push all the safety clips into their places.
12.Assemby the safety screw and nut together to secure connection of both grids.
OPERATION
1.Please check the voltage information and make sure it matches the one in your country.
2.Place the device on flat, stable surface.
3.Use the speed control buttons (5) to operate the fan. Press proper switch to turn on the required speed. The fan has got 4 speed
positions:
0 = off; 1 = low speed; 2 = medium speed; 3 = fast speed.
4.Oscillation control: To make the fan oscillate in the left and right direction, press the oscillation button (11) down, it is located at the top
of motor housing (4). To stop oscillation, pull up the oscillation button (11).
5.Tilt control: Adjust the fan head (1+2+3) to the desired angle by pushing the motor unit (4) a little up or down direction.

CLEANING AND MAINTENANCE

CAUTION: Do not allow the fan's motor unit (4) or any buttons to get wet.
1. Before cleaning remove the plug from the electrical socket.
2. To clean dust from the fan propeller (2), remove the front grid (1). Remove the fan propeller (2) from the motor shaft (10), wipe with a
damp cloth, then wipe dry.
3. In order to clean the motor unit (4) gently wipe it with a damp cloth, without detergents. Wipe it dry.
4. Store the fan in a dry place.
TECHNICAL INFORMATION:
Diameter 40cm / 16"
Noise level 53,6 Db
To protect your environment: please separate carton boxes and plastic bags and dispose them in corresponding waste
bins. Used appliance should be delivered to the dedicated collecting points due to hazarsous components, which may
effect the environment. Do not dispose this appliance in the common waste bin.
ALLGEMEINE SICHERHEITSVORSCHRIFTEN LESEN SIE AUFMERKSAM WICHTIGE
ANWEISUNGEN BEZÜGLICH DER SICHERHEIT DER BENUTZUNG BEWAHREN SIE
Bei Verwendung des Gerätes zu gewerblichen Zwecken werden die Garantiebedingungen
geändert.
1.Vor dem ersten Gebrauch, die Bedienungsanleitung lesen und die dort angegebenen
Hinweise beachten. Der Produzent trägt keine Verantwortung für Schäden, die aufgrund
von bestimmungswidriger Nutzung oder unsachgemäßer Bedienung entstanden sind.
2.Das Gerät ist nur für den Hausgebrauch verwendet. Verwenden Sie es nicht für andere
Zwecke als den bestimmungsgemäßen Gebrauch.
3.Das Gerät ausschließlich an die Steckdose 220-240 V ~ 50/60 Hz anschließen. Es darf
nicht zu anderen, bestimmungswidrigen Zwecken benutzt werden. Wegen
2.Propeller
6.Pipe (6A inside, 6B outside)
10.Motor shaft
Max Power: 90W Power: 40W
DEUTSCH
DIESE FÜR DIE ZUKUNFT AUF
3.Rear grid
7.Base cover
11.Oscillation button
Power supply 220-240V ~ 50Hz
4
4.Motor unit
8.Screw