Steps To Follow - Bi-pedaler 3821 Manual De Instrucciones

around the device.
BI-PEDALER® INSTRUCTION MANUAL
PRODUCT COMPONENTS
Do not do any other exercises, since
you may injure yourself by using the
Product Description: A. Screws x 3
B. Screws x 2 device incorrectly.
1. Horizontal bar
C. Washers x 2
2. Base tubes
Warning: If any of the adjustment devi-
D. Nuts x 2
3. Rear bar
ces are left projecting, they could inter-
E. Tool x 1
4. Lower shaft
F. Wrench x 1 fere with the user's movement.
5. Upper shaft
G. Screws x 2
6. Height-adjustment knob
Class HC
H. Washers x 2
7. Hand exerciser
Set-up
I. Nuts x 2
8. Foot exerciser
J. Screws x 3 First unpack all the parts.
9. Resistance-adjustment knob
Safety Warnings
Read the instruction manual before

STEPS TO FOLLOW:

I. Attach the horizontal bar (1) to the 2 base tu-
using BI-PEDALER® for the first time.
bes (2) using the A screws (which are stuck to
If you have any doubts about your phy-
the base tubes (2)). You will need tool E to attach
sical condition or have suffered from them. Make sure they are firmly attached.
an illness, always consult your doctor
II. Attach the rear bar (3) to the base tube (2) as
before using BI-PEDALER®.
shown in the photo. Attach it with the B screws,
If you have a spinal disc herniation, C washers and D nuts using tool E and wrench F.
consult your doctor before using the
III. Attach the lower shaft (4) and the upper shaft
product.
(5) using the J screws, which are stuck to the bar.
If you have asthma or suffer from a Use the E tool to attach them.
respiratory disease, consult your doc-
VI. Now attach the unit made up of the joined
tor before using BI-PEDALER®.
lower and upper shafts to the base tube (2), as
Always place the device on leveled shown in the photo, using the B screws, C was-
hers and D nuts. You will need to use tool E and
base.
wrench F. Tighten enough to allow the bar to move
Ensure that children do not use BI-
on its axis.
PEDALER® without adult supervision.
V. Attach the joined lower shaft and upper shaft
Do not use if you are pregnant.
so it is resting on the rear bar (3), as shown in
Do not drink alcoholic beverages while
the photo. Attach them with the height adjustment
knob (6). You can choose the height that works
using the device.
best for you from 6 different heights.
Drink water after use.
The maximum weight allowed on the
VI. Now take the hand exerciser (7) and remove
BI-PEDALER® is 100 kg. the A screws. Place the hand exerciser in the hole
in the shaft by inserting the tabs and attach it with
For a safe, comfortable workout, lea-
the A screws using tool E. Make sure the exerciser
ve a minimum of 0.6 m of free space
is firmly attached.
VII. Place the foot exerciser (8) on the rear bar, as
shown in the photo. Attach it using the 2 G screws,
H washers and I nuts.
Instructions for Use
BI-PEDALER® is not a professional piece of sports
equipment. It is not recommended for use in a
standing position. The user should be seated on a
sofa or chair when using the device.
BI-PEDALER® has 6 different heights. Choose
the one that works the best for you and insert the
height-adjustment knob (6) in the corresponding
hole.
The resistance of the hand and foot exercisers can
be adjusted using the resistance-adjustment knob
(9). Set the resistance that works best for you.
Important notice: After 7 minutes of use, do not
touch the hand or foot exerciser to prevent burns.
1 m
0,6 m
FOLDING INSTRUCTIONS
1. Unscrew the resistance-adjustment knob (9) on
the foot exerciser.
2. Unscrew the height-adjustment knob (6).
3. Fold the device as shown in Figure A.
4. Screw the height-adjustment knob (6) back into
one of the holes.
5. Screw the resistance-adjustment knob (9) into
the top hole on the shaft. See Figure B.
To assemble BI-PEDALER® again, repeat the
steps in reverse order.
BI-PEDALER® comes with a magnetic bracelet
as a free gift. For maintenance purposes, keep it
from becoming wet.
Precautions:
• This product is not a toy and should be kept
out of reach of children.
• If you are pregnant or think you might be, do
not use the device or use it only after consul-
ting your doctor.
• Patients with heart problems or implants
should not use the device.
• Patients with haemophilia, thrombocytopenia
or other blood disorders should not use the
device unless authorized by their doctor.
• The permanent magnet may cause allergies.
If this occurs, stop wearing the bracelet.
Quality Warranty:
This product is covered by a warranty against
manufacturing defects subject to the time perio-
ds stipulated by the legislation in force in each
country.
This warranty does not cover damages resulting
from inadequate use, negligent commercial use,
abnormal wear and tear, accidents or improper
handling.
Australia & New Zealand only
This product has the benefit of certain Consu-
mer Guarantees. These are prescribed by the
Australian Consumer Law & the New Zealand
Consumer Guarantees Act 1993 both of which
provide protection for consumers. There is no
express warranty for this product in Australia or
New Zealand. The above paragraph refers to
other countries.
Made in China.