Fein MOtlx 6-25 Manual De Instrucciones página 12

en
12
j) Do not machine any material containing asbestos.
Asbestos is cancerogenic.
k) Keep your hands away from the application tool. Do
not reach in front of or below the application tool.
Contact with the application tool can lead to injury.
Application tools can become very hot while
working.
l) Only position the pneumatic tool onto the workpiece
when it is switched on. There is danger of kickback
occurring or of losing control over the pneumatic
tool.
m) It is forbidden to rivet or screw any name-plates or
signs onto the pneumatic tool. Use adhesive labels.
n) Do not use any accessories that have not been spe-
cifically designed and recommended by the manufac-
turer of the pneumatic tool. Operation is not auto-
matically safe because an accessory happens to fit
your pneumatic tool.
o) Beware of any concealed electric cables, gas or wa-
ter conduits; check the working area with a metal
detector, for example, before commencing work.
5) Service
a) Your pneumatic tools should only be repaired by
qualified specialists and only with original spare
parts. This will ensure that the safety of the pneu-
matic tool is maintained.
Special safety instructions.
Secure the workpiece firmly. A work piece that is
gripped tightly in a clamping device or vice, is more
secure than if held by hand.
For all work or when changing application tools, always
wear protective gloves. Danger of injury from the sharp
edges of the application tools. Application tools can
become very hot while working. Danger of burns!
Never direct the application tool against yourself. Hold the
pneumatic tool in such a manner that the application tool
cannot come into contact with your hand.
Hand/arm vibrations.
Whilst working with this power tool, hand/arm vibra-
tions will occur.
Adopt the correct working practices in order to reduce
the exposure to vibration:
– in the case of strong vibration, take the recom-
mended work breaks or change your task more fre-
quently,
– keep your hands warm,
– whilst working, only grip the power tool as firmly as
necessary,
– work only with technically sound machines and
application tools,
– wear vibration-damping work gloves,
If these recommendations are not observed, the expo-
sure to strong vibration during daily work over a longer
period of time can be detrimental to health.
The maximum exposure values stipulated in the indus-
trial safety directives (e. g. in directive 2002/44/EC, a
maximum daily exposure limit of 5 m/s
normal duration of 8 hours) must not be exceeded.
The value of the estimated weighted acceleration
obtained in the laboratory can serve for predicting the
exposure to vibration. During work, weighted acceler-
ations will be dependent on the particular application,
and deviation from this laboratory value can occur.
Emission values for sound and vibration
(Two-figure – specifications as per ISO 4871)
Vibration
Classification of FEIN
application tools accord-
ing to vibration class
VC0
VC1
VC2
VC3
VC4
VC5
K·
* These values are based on a work cycle consisting
of no-load and full-load operation of the same dura-
tion.
For information on the vibration class assigned to the
application tool, please see the enclosed data sheet
3 41 30 562 06 0.
Intended use of the pneumatic tool.
hand-guided pneumatic tool for commercial use, for
cutting plastic beads and similar materials, particularly
for cutting out windscreens, rear and side window
panes for the automobile workshop using the applica-
tion tools and accessories recommended by FEIN.
Connection to air supply.
For trouble-free operation of the air tool, use a filter/
regulator-lubricator consisting of water separator, oil
lubricator and compressed-air regulator.
Check that the pressure in the compressed-air supply
conforms with the pressure given on the rating plate on
the pneumatic tool.
The hose should have a minimum diameter of 16 mm.
The opening of the valve and the coupling should have
a diameter of at least 8 mm.
Operating instructions.
When uncoupling hose couplings, first shut the ball
valve, then actuate the pneumatic tool, and then uncou-
ple. Do not uncouple the hose coupling until after the
compressed air has been completely relieved.
Repair and customer service.
Maintain and clean the pneumatic tool every 300 work
hours or every 6 months.
2
relating to a
Weighted acceleration*
Before connecting, blow through the hose.
2
< 2.5 m/s
2
< 5 m/s
2
< 7 m/s
2
< 10 m/s
2
< 15 m/s
2
< 30 m/s
2
1.5 m/s