Silverline 252190 Manual Del Usuario página 7

252190
the use of personal protective equipment (PPE) as a control measure.
• The user must have a rescue plan and the means at hand to implement it
• The plan must take into account the equipment and special training necessary
to effectively conduct prompt rescue under all foreseeable conditions
Accessories
• Additional fall arrest gear, workwear and other personal protection equipment
is available from your Silverline stockist
Maintenance
Note: All fall arrest equipment must be regularly inspected, cleaned and
maintained by a competent person, in accordance with local laws and
regulations. Maintenance must be recorded in a dedicated service record (see
end of this manual).
WARNING: Carry out a visual and tactile inspection of all components every
time the equipment is used. Carry out a detailed examination if the equipment
has not been used for some time. Note: A thorough, detailed examination of
the equipment must be carried out at regular intervals, at least once annually, or
more frequently depending on use.
WARNING: It is ILLEGAL to carry out any kind of repair or modification to
this equipment.
WARNING: Should any damage be detected, remove the equipment from
service immediately. It must then be rendered unusable and discarded.
Inspection procedures
• The following procedure helps detect defects potentially resulting in
degradation and/or weakening of the Karabiner (2) and Scaffold Hook (1) :
1. Inspect for missing or altered parts. Refer to the image in 'Product
Familiarisation' for identification. Verify each item is present and has not been
tampered with
2. Inspect the entire karabiner or hook for cracks, nicks or breaks in the metal.
Inspect every millimetre
Note: If necessary, clean before inspection, so that even small hairline cracks
are visible.
3. Inspect for deformation, bent or dented parts. Open the gate and inspect the
nose of the karabiner or hook for signs of wear, distortion or damage
4. Inspect the metal surface for any signs of corrosion. Steel karabiners and
hooks may show red dust as evidence of corrosion; aluminium karabiners
may develop pitting or scales
5. Inspect for heat damage, which can usually be seen as discolouration or
darkening of the metal surfaces
6. Perform a functional test: The locking mechanism must function easily, and
the karabiner or hook must fully open and close smoothly and easily. When
locked, the gate MUST NOT open under pressure from any direction
• Slowly pass the rope through your hands to detect small defects, abrasions
and twist damage. Feel for softening and hardening of fibres and look for
ingress of contaminants
• The following defects potentially result in degradation and/or weakening of
the lanyard:
• Cut/broken fibres or nicks
• Kinks, knots (other than those intended by the manufacturer) or hockling
(unravelling due to constant turning of the rope in the same direction, or
due to shock loading)
• Brittle, fuzzy or worn fibres, fraying or abrasions
• Overall deterioration or discolouration
• Any kind of modification/attempted repairs
• Hard or shiny spots, fused fibres or strands
• Heat or friction damage indicated by fibres with a glazed appearance which
may feel harder than surrounding fibres
• Burnt, charred or melted fibres or strands
• Change in diameter, compared to the original diameter (see 'Specification')
• Rope marked with paint or a permanent marker
• Loose, missing, deformed or damaged Rope Thimbles (3)
• Eye damage (cuts, nicks, fraying, fusing, abrasion etc.)
Restraint Positioning Lanyard
• Damage to protective covers/sleeves/sheaths
• Splices starting to unravel, or showing signs of damage or deterioration
• Partially deployed energy absorber (e.g. short pull-out of tear webbing)
• Damage to stitching
• Chemical attack potentially resulting in local weakening and softening
(often indicated by flaking of the surface)
• UV light degradation which can be difficult to identify, particularly visually,
but there may be some loss of colour (if dyed) and a powdery surface
• Contamination (e.g. with dirt, grit, sand etc.) which may result in internal or
external abrasion
• Damaged, oxidised or deformed fittings (e.g. karabiners, screw link
connectors, scaffold hooks)
• Inspect all other components or subsystem of the fall arrest equipment
according to manufacturer's instructions
• Record inspection date and results in a dedicated service record (see end of
this manual)
Note: Refer to 'Service life and product obsolescence' if any damage or other
defects are detected during inspection
Cleaning
Note: Correct cleaning is essential to ensure integrity of this equipment. Follow
the cleaning instructions below without deviation.
• Clean the karabiner and hook by wiping it with a soft, lightly oiled cloth
• If this is not sufficient, use warm water with a mild pH neutral (pH 7)
detergent, to clean off any foreign matter. Dry thoroughly and lubricate
moving parts with a suitable spray lubricant
• Clean lanyard in warm water (30 – 60°C) with a mild pH neutral (pH7)
household detergent. In case of minor soiling, wipe with a cotton cloth or
carefully clean using a soft brush
• DO NOT under any circumstances use any abrasive materials, acids, basic
detergents or solvents
• Disinfect parts that come into contact with the operator's skin, using a
disinfectant suitable for the material of the equipment (see 'Specification').
Strictly follow the disinfectant manufacturer's recommendations and
procedures
• ALWAYS allow the equipment to dry naturally, and keep it away from open fire
or any other heat source
Note: This also applies to equipment that has become wet during use.
Lubrication
• Occasionally apply a small amount of a suitable spray lubricant to the
gate mechanism of the karabiner and hook. Afterwards, perform a thorough
inspection as described in 'Inspection procedure'
Transport
• ALWAYS transport this equipment inside a dedicated bag or suitable container
that protects it from mechanical damage and shields the equipment from high
temperatures, humidity, UV rays and chemicals
Storage
• Store this tool carefully in a secure, dry place out of the reach of
children
• Store at moderate temperature and humidity, away from direct
sunlight or chemicals, inside a dedicated, UV-proof bag or container
• Never place heavy objects on top of this equipment
Disposal
Service life and product obsolescence
WARNING: Fall arrest equipment is designed to arrest a fall from height
ONLY ONCE! If subjected to an arrested fall, the gear must be withdrawn from
service and rendered unusable.
Note: The date on which the product is removed from the original packaging
for the first time becomes the 'date of first use' , which should be recorded on the
Inspection Record (see end of this manual). The specified working life begins
from this point.
silverlinetools.com
7