Product Characteristics - YATO YT-04701 Manual Del Usuario

All manuals and user guides at all-guides.com
GB

PRODUCT CHARACTERISTICS

Induction cooker is intended for heating, cooking and preparing of dishes in the vessels designed for use in induction cookers.
With the power adjustment you can adjust the parameters of the cooker to suit your needs. Correct, reliable, and safe operation
of the device is dependent on its proper use, therefore:
Prior to working with the product, you should read all the instruction and keep it around.
For any damages or injuries caused by the product misuse, non compliance with with safety regulations and recommendations
included in this manual, the supplier does not accept any liability. Using the product incorrectly, results also in the loss of user's
rights to the guarantee, as well as a warranty.
EQUIPMENT
The cooker is supplied in a complete state and requires no assembly. Before using the product you should, however, remove all
packaging and protection for transport. They are also required preparatory steps described later in this manual.
GENERAL RECOMMENDATIONS FOR USE
The product has been designed for professional use and its operation should be carried out by properly qualified personnel.
The product is only used for heating, cooking and dishes preparing in the vessels intended for use in induction cookers. It is forbid-
den to use the device in another capacity, place the food directly on the hotplate.
It is forbidden to repair independently, disassembly or modification of the product. Any repairs must be carried out by an author-
ized repair service.
During the operation, you should supervise the product all the time.
WARNING! During its operation the product heats up to high temperatures, you should not touch the walls of the product during
its operation, it can cause serious burns.
The product is not intended for use by children at least 8 years of age and persons with reduced physical abilities, mental abilities
and people with lack of experience and knowledge of the equipment. Unless there will be supervised or instruction will be carried
out regarding the use of the product in a safe manner so, so that the associated risks would be understood. Children should not
play with the product. Children without supervision should not carry out the cleaning and maintenance of the device.
Recommendations for transport and installation of the product
ATTENTION! Installation and connection of the product may be made only by qualified personnel.
The product may only be placed on a hard, flat, even and non-flammable surface. The substrate should withstand the weight of
the device, and a vessel placed on it.
You should provide space for at least 10 cm around the lateral walls of the product, do not place materials that are not resistant to
high temperatures above the product. This will allow for proper ventilation of the product. Do not place eg. a table near the edge.
Any electrical devices should be placed above the product. During operation water vapor is released, it can cause an electrical
short circuit and cause electric shock.
It is forbidden to drill any holes in the product, as well as any other product modification, which is not described in the manual.
Product may be transported only in the cold state, by grabbing it by its case. Do not transport the product by pulling on the power
supply cord.
On the back of the product and in its vicinity you should not put any metal objects and surfaces.
The temperature at the place of installation and operation of the product must be in the range of + 10 C ÷ +38 C, and relative
O O
humidity must be below 90% without condensation of water vapor.
Guidelines for connecting the product to the power supply
Before connecting the product to mains, you should make sure that voltage, the frequency and the performance of the mains
correspond to the values on the rating plate of the product. Power cable plug must fit into the mains socket. It is forbidden to alter
the plug.
The product must be connected directly to a single wall mains socket. it is forbidden to use extension cables, splitters and double
sockets. Circuit power supply network must be equipped with a protective cord and protection for 16 A.
Avoid contact of the power cable with sharp edges and hot objects and surfaces. When the product is working, the power cable
must always be fully unwind, and its location should be set so, it would be no obstacle during the operation of the product. Placing
the power cable can cause a tripping hazard. The power outlet should be located in such a place, that there would be always
possible to quickly disconnect the power cable plug. When disconnecting the power cable plug, you should always pull by the
plug housing, never by the cable.
If the power cable or plug are damaged, you should immediately disconnect them from the mains and contact authorized service
of the manufacturer for replacement. Do not use the product with a damaged cable or plug. The power supply cable or plug may
not be repaired in the event of a failure of these elements they should be replaced with a new ones, free from defects.
O R I G I N A L I N S T R U C T I O N S
7