Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
REPLACING THE FILTER
CAUTION: Unplug from outlet and allow to cool for 60 minutes before
replacing filter.
Replace the filter every six months of regular use for optimal performance.
Follow the steps below:
1. The filter is located at the bottom of the base. Gently squeeze the latches on the filter
1
cover to remove it.
2
2. Remove and replace the filter, ensuring the pull tab is still visible on top of the filter.
3
3. Snap the filter cover back into position.
Note: Filter must always be used to ensure proper performance.
4
D
C
B
A
4
WARRANTY
This appliance is warranted against defective material or workmanship for a period of
one year from the date of purchase. Any defective part will be repaired or replaced at no
charge if it has not been tampered with and appliance has been used according to these
printed instructions. This warranty gives you specific legal rights as well as other rights
which vary from state to state.
This warranty does not cover a defect that has been caused by negligence, accidents or
improper use of the appliance. To keep your Dr. Brown's™ Bottle Sterilizer and Dryer in
good condition and retain your warranty, USE ONLY AS DIRECTED.
CUSTOMER SERVICE
If you experience unsatisfactory operation or have any questions/comments,
call Handi-Craft's Customer Service at 1-800-778-9001 or send an email to
info@handi-craft.com.
For purchases made outside the United States and Canada, please contact your
local distributor.
7
3
2
B
A
DESIGN UNITS: MILLIMETERS
TOLERANCES UNLESS NOTED:
2 f ilters are included.
NO PLACE:
X
2.5
ONE PLACE:
.X
0.5
TWO PLACE:
.XX
0.25
THREE PLACE:
.XXX
0.13
ANGLE:
X
0.5
ANGLE:
.X
0.25
THIRD ANGLE
To purchase replacement filters:
PROJECTION
drbrownsbaby.com
3
2
2
1
THIS DRAWING AND RELATED 3D CAD DATA
HANDI-CRAFT COMPANY
CONTAINS PROPRIETARY INFORMATION THAT
ARE THE PROPERTY OF
HANDI-CRAFT CO. AND ARE NOT TO BE
COPIED OR USED WITHOUT THE PERMISSION
4433 FLYER AVE. ST. LOUIS MO. 63116, USA
OF HANDI-CRAFT CO.
INTERPET PER ASME Y14.5-1994
DRAWN
RBW
OTHER HANDI-CRAFT ENGINEERING
STANDARDS MAY APPLY
ENG APPR.
SOLIDWORKS
3D
MFG/Q.A APPR.
2
DESIGN UNITS: MILLIMETERS
DRAWN
RBW
15JUL19
HANDI-CRAFT COMPANY
TOLERANCES UNLESS NOTED:
ENG APPR.
NO PLACE:
X
2.5
4433 FLYER AVE. ST. LOUIS MO. 63116, USA
ONE PLACE:
.X
0.5
MFG/Q.A APPR.
TWO PLACE:
.XX
0.25
TITLE:
THIS DRAWING AND RELATED 3D CAD DATA
THREE PLACE:
.XXX
0.13
FILTER REPLACEMENT
CONTAINS PROPRIETARY INFORMATION
ANGLE:
X
0.5
THAT ARE THE PROPERTY OF
ANGLE:
.X
0.25
HANDI-CRAFT CO. AND ARE NOT TO BE
COPIED OR USED WITHOUT THE
PERMISSION OF HANDI-CRAFT CO.
DO NOT SCALE DRAWING
SIZE
C
DWG. NO.
REV.
1
INTERPET PER ASME Y14.5-1994
THIRD ANGLE
OTHER HANDI-CRAFT ENGINEERING
STANDARDS MAY APPLY
PROJECTION
MATERIAL
SOLIDWORKS
3D
SCALE: 1:1
SHEET 1 OF 1
1
D
C
B
TITLE:
FILTER AND COVER
SIZE
DWG. NO.
A
MATERIAL
15JUL19
DO NOT SCALE DRAWING
SCALE: 1:2
A
1
B
A
REV.
1
SHEET 1 OF 1
1
Publicidad
Tabla de contenido
