Wiring Diagram; Spring Start-Up - Marquis WM 35 Guia De Inicio Rapido

• Connect water supply line.
Install a sillcock and water
valve on faucet as shown by
figure 4. Place the nut and
ferrule on the tubing and
tighten the nut until water
tight.
• Install float valve. Install
valve in the provided hole in
corner post (Fig. 5) and at-
tach water supply line.
• Fill pan. Allow water to
fill to within 1" of top of pan
and adjust float to main-
tain this water level. This
can be accomplished by
bending the float rod (Fig.
5).
• Adjust water amount.
Your cooler is equipped
with a unique water me-
tering valve (Fig. 6). The
amount of water delivered to
the pads may be decreased by
pressing the plastic valve as
the arrows indicate. If water
is splashing out of water
troughs, you may need to de-
crease the amount of water
delivery. Check to see that all
pads are saturated with water
and that there are no dry spots
or openings in the pads.
MAINTENANCE
WARNING:
Before doing any maintenance be sure
power is off and unit is unplugged. This is for your safety.

SPRING START-UP

• Clean pump. Cleaning the pump is necessary once a year
at start-up. For your safety, turn unit off and unplug from
power receptacle. Remove the pump from the mount slot.
Remove the base of the pump as shown in Fig. 7. Clean
the pump and turn the impeller to ensure free operation.
Remove the pump spout and check for any blockage. After
cleaning, reinstall the base onto the pump. Reattach the
pump to the mount in
the cooler using the
plastic retainer to en-
sure that the pump will
not overturn. Do not
forget to replace the
spout and water deliv-
ery tube onto the pump
outlet. The pump has
automatic reset thermal
protection.
110529
All manuals and user guides at all-guides.com
FAUCET
SILLCOCK
FIG. 4
WATER
SUPPLY LINE
CORNER POST
FLOAT ROD
FIG. 5
INCREASE
DECREASE
FIG. 6
DEPRESS HERE
TO REMOVE
FIG. 7
• Change Pads. Aspen pads should be replaced once or
twice a season, depending upon the length of the season.
At the beginning and at mid season a clean pad is more
absorbent and efficient and will deliver substantially more
cool air.
• Oil bearings. The blower bearings and cooler motor in this
unit should be oiled with a few drops of non-detergent 20/
30 weight oil once each year. The motor does not need oil
if it has no oil lines for oiling. Motors that have no lines are
lifetime oiled at the factory and require no further oiling for
the life of the unit.
CAUTION:
Do not over oil. Over oiling can cause mo-
tor burn out, due to excessive oil
getting into motor winding.
• Check belt tension. A 3 lb.
force should deflect the belt 3/
4 inches (see Fig. 8). Read-
just belt if needed.
WINTER SHUT DOWN
• Drain water. Always drain all of the water out of the cooler
and water supply line when not in use for prolonged peri-
ods, and particularly at the end of the season. Keep the
water line disconnected from both the unit and water sup-
ply so that it does not freeze.
• Cover unit. To protect the life of the finish, a cover for the
unit is suggested in extended periods of non-use.
• Unplug unit from power supply during extended peri-
ods of non-use.
By following the operating, installation, and maintenance sug-
gestions as outlined, you can get many years of efficient and
satisfactory service from your cooler. In the event additional
information is desired, your dealer will be more than glad to
assist you in every possible way.

WIRING DIAGRAM

WHITE-COM
BLOWER
BLACK-HI
MOTOR
RED-LO
PUMP
MOTOR
RIBBED-COM
GREEN
GREEN-GROUND
3 LB.
3/4 INCHES
FIG. 8
SWITCH
4
B
3
PLAIN
PLAIN
2
A
1
RIBBED-COM
WIRE CONNECTOR
3