Descargar Imprimir esta página

GUILCOR RAYTEMP 8 Manual Del Usuario

Publicidad

Enlaces rápidos

Supplied by Guilcor
www.guilcor.com/ contact@guilcor.com
RAYTEMP
Infrared Thermometer
Operating Instructions
Product code:
AR005933
INSTRUMENT OPERATION - Simply aim the RayTemp 8 Infrared (IR) Thermometer at the
target and press the trigger to measure the surface temperature. The scan icon '
displayed. When the trigger is released the reading is automatically held for 60 seconds and
'HOLD' will be displayed, after which the thermometer will shut down.
MEASUREMENT ZONE/TARGET DISTANCE - The measurement zone is proportional to the
distance the RayTemp is away from the target. The RayTemp 8 is equipped with a 12:1 lens. If
the target is 60 cm (24 ") away the measurement zone will be 5 cm (2 ") across.
EMISSIVITY - The RayTemp 8 has a default emissivity of 0.95 but is adjustable from 0.10 to
1.00. The closer the emissivity value is set to the actual emissivity value of the object being
measured, the more accurate the readings will be. To adjust the emissivity press the MODE
button so that 'E' is display, press the button again so that '
and DOWN
buttons to set the emissivity required. Please note: non-contact infrared
thermometers are not recommended for use in measuring shiny or polished surfaces.
LASER POINTER - The circular laser function can be turned on or off by pressing the trigger
and simultaneously pressing the °C/°F button whilst the trigger is being pressed. The centre
of the measurement zone is 14 mm (approximately ½ ") above the lowest laser dot with the
instrument held in a horizontal position. For safety, the laser pointer will only activate when
the trigger button is pressed. The laser module is a Class 3 device that has a maximum
power output of less than 5 mW at a wavelength of 660 nm. Prolonged, continuous
exposure, such as staring at the beam, can be harmful and should be avoided. DO NOT look
at the beam of any optical instrument.
LCD BACKLIGHT - The LCD backlight function can be turned on or off by pressing the
trigger and simultaneously pressing the LOCK button whilst the trigger is being pressed.
The backlight icon '
' will be shown to indicate on or off.
UNDER RANGE/OVER RANGE - If the measured temperature goes below or above the
range of the instrument, 'Er' will be displayed. When the measured temperature returns
within the range of the instrument, readings will automatically be displayed.
THERMOCOUPLE PROBE/SENSORS - To display the thermocouple probe temperature,
press the MODE button until 'PRB' is displayed. If the thermocouple breaks or is not
connected, the instrument will display 'noP'. The RayTemp 8 should only be used with
thermocouple type K nickel-chromium/nickel-aluminium probes or sensors that meet BS
EN 60584:1996 standard and are fitted with a suitable miniature thermocouple plug. To
review the max or min temperatures of the connected probe whilst in PRB mode press the
DOWN
button for min and the UP
button for max.
8
®
' will be
' is displayed. Use the UP

Publicidad

loading

Resumen de contenidos para GUILCOR RAYTEMP 8

  • Página 1 MEASUREMENT ZONE/TARGET DISTANCE - The measurement zone is proportional to the distance the RayTemp is away from the target. The RayTemp 8 is equipped with a 12:1 lens. If the target is 60 cm (24 ") away the measurement zone will be 5 cm (2 ") across.
  • Página 2 ES - FUNCIONAMIENTO DEL INSTRUMENTO - Simplemente apunte con el Termómetro de Infrarrojos RayTemp 8 al objetivo y oprima el gatillo para medir la temperatura de la superficie. La pantalla the MODE button until 'MAX' is displayed. To access the minimum reading, press the MODE mostrará...
  • Página 3 ZONE DE MESURE / DISTANCE PAR RAPPORT À LA CIBLE - La zone de mesure est proportionnelle à la RayTemp se encontra do alvo. O RayTemp 8 está equipado com uma lente 12:1. Se o alvo estiver a 60 cm distance entre le RayTemp et la cible.
  • Página 4 RayTemp von der Zielfläche. Das RayTemp 8 ist mit einer 12:1-Linse ausgestattet. Wenn die Zielfläche 60 distanza del RayTemp rispetto all'obiettivo. Il RayTemp 8 è dotato di una lente 12:1. Se l'obiettivo si trova a cm entfernt ist, umfasst der Messbereich einen Durchmesser von 5 cm.

Este manual también es adecuado para:

Ar005933