FRAM Fresh Breeze CF8046A Boletín De Instalación

CF8046A
Installation Bulletin:
Bulletin d'installation :
Boletín de Instalación:
Estimated time of installation:
Temps estimé pour l'installation :
Tiempo estimado de instalación:
Application:
Ford Contour | Mercury Cougar | Mercury Mystique
Application:
Aplicación:
For more application specifics,
please refer to our catalog.
Pour obtenir plus d'information
sur les applications, veuillez
consulter notre catalogue.
Para obtener información
específica sobre la aplicación,
consulte nuestro catálogo.
FRAM Group Operations LLC
Danbury, CT 06810-5109 U.S.A.
©2012 FRAM Group IP LLC
FRAM Group (Canada) Inc.
2430 Meadowpine Blvd.
Unit 105 & 107
Mississauga, ON
L5N 6S2 Canada
SOME VEHICLES MAY DIFFER SLIGHTLY. IF YOU HAVE QUESTIONS
REGARDING THIS FILTER, ITS INSTALLATION OR MORE DETAILS
SPECIFIC TO YOUR VEHICLE, PLEASE VISIT
www.framfreshbreeze.com
FOR HOW-TO VIDEOS AND ADDITIONAL INFORMATION.
CERTAINS VÉHICULES PEUVENT PRÉSENTER DES DIFFÉRENCES. SI VOUS
AVEZ DES QUESTIONS CONCERNANT CE FILTRE, SON INSTALLATION OU
DÉSIREZ OBTENIR PLUS DE DÉTAILS CONCERNANT VOTRE VÉHICULE,
VEUILLEZ VISITER LE www.framfreshbreeze.com POUR OBTENIR
DES DÉMONSTRATIONS VIDÉOS ET PLUS D'INFORMATION.
PUEDE VARIAR UN POCO EN ALGUNOS VEHÍCULOS SI TIENE PREGUNTAS
SOBRE EL FILTRO Y LA INSTALACIÓN O DESEA INFORMACIÓN EN DETALLE
PARA SU VEHÍCULO, VISITE www.framfreshbreeze.com, DONDE
ENCONTRARÁ VIDEOS INSTRUCTIVOS E INFORMACIÓN ADICIONAL.
Importado por:
FRAM Group Operations Mexico City S.A. de C.V.
Carretera México-Cuautitlán km 31.5 S/N
Nave 5, Conjunto Industrial Cuautitlán.
Col. Loma Bonita
Cuautitlán, Edo. de México
MEX, C.P. 54800
Tel. 01 800 7154 135
Hecho en China
TOOLS: Standard Screwdriver or Blade to pry with and T-20 Torx Driver.
LOCATION OF CABIN FILTER: In front of the windshield under the vent grille on the passenger side of the vehicle.
REMOVE ALL DEBRIS IN AND AROUND FILTER LOCATION.
07-10
1. Sit in the driver side seat. Insert the key in the ignition and turn on the car.
15 minutes or less
15 minutes ou moins
2. Turn on the windshield wipers, then turn off the ignition while the wipers are in the upright position. (Fig 1)
15 minutos máx.
3. Go outside to the passenger side windshield and in front of the bottom side of the windshield you will see two screw caps at
the top of the cowling. Using the Blade or Standard screwdriver gently pry off the screw caps. Once the caps are removed, use
the Phillips-head screwdriver to remove the two screws. (Fig 2)
4. Open the hood. Now gently pull back the rubber weather strip from the front of the passenger side cowling. (Fig 3)
5. On the bottom of the same cowling you removed the two screws, you will see two Torx screws. Remove these by using the T-20
Torx driver to unscrew them. (Fig 4)
6. Remove the passenger side cowling. (Fig 5)
7. You should now see the filter and housing. Use the Standard blade screwdriver and pry the two clips securing each end of the
housing loose. (Fig 6)
8. Slide the filter and housing straight up and remove. (Fig 7)
9. Remove the dirty filter from the housing. (Fig 8)
10. Install new filter in housing. The filter has slits cut along the top of it to allow it to bow to fit the housing properly.
11. Reinstall the new filter and housing into the vehicle and use a Standard blade screwdriver to reengage the two clips on each side.
12. Put the passenger side cowl back in place and reinstall the two T-20 Torx screws and tighten them.
13. Reinstall the weather strip back in place and make sure it is secure.
14. Close the hood and reinstall the two top screws that you removed earlier along with the caps. The caps should just snap back
on top of the head of the screw.
15. Sit in the driver side seat and insert key in ignition and turn car on. With the car running, turn off windshield wipers so they return
to their original position and turn off ignition.
1
5
3
2
6 7
4
8