Customer Support - Nacon RC-500 Manual Del Usuario

EN
n
Thank you for purchasing the NACON RC-500 Racing Seat. This product
has been designed to enhance your video gaming experience. Please keep this
instruction manual for future reference.
WARRANTY
This product bearing the NACON trademark, is guaranteed by the manufacturer
for a period of 2 years from the date of purchase, and will, during this period be
replaced with the same or a similar model, at our option, free of charge, if there
is a defect due to faulty material, or workmanship. This guarantee does not cover
defects arising from accidental damage, misuse or wear and tear. This does not
affect your statutory rights. Please retain your proof of purchase, for the duration
of the warranty period, in case of a product replacement claim. Without this
unfortunately we cannot process your claim.
PACKAGE CONTENTS
1 x Installation guide
1 x Seat with rails and lever
1 x Security mat
2 x Seat brackets
1 x Front frame with foot plate
1 x Back frame
8 x Frame feet
2 x Lower wheel support stand
2 x Upper wheel support stand
2 x Connecting tubes
1 x Gear shift plate
1 x Gear shift plate arm
4 x Knurled screws short
2 x Knurled screws long
4 x Velcro cable holders
1 x Blister card with screws, nuts and tools
ASSEMBLY
We recommend to assemble the RC-500 Racing Chair with the help of a second
person, as assistance may be required to assemble the chair.
1. Remove the foot plate from the front frame by unscrewing and put the screws
and frame aside for future use.
2. Insert 4 of the frame feet into the prepared holes and screw them in tightly.
3. Attach the lower wheel support stand to the side plates of the front frame by
using a screw and a nut and a long knurled screw for each. The different holes
for the screws allow you to select your preferred angle for the wheel support.
Then insert each upper wheel support stand into the tube of the lower one with
the vertical area facing inwards.
4. Attach the foot plate with the NACON logo closest to the seat area.
5. Screw the wheel support onto the support stands using a total of 4 screws
and nuts.
6. Adjust the wheel support to the desired height and fix it on each side with a
knurled screw.
7. (Optional) If you wish to use a gear shift with your steering wheel, attach the
gear shift plate to the gear shift plate arm, the side depending on the hand you
want to use the gear shift with. Then attach the plate to either the left or right
wheel support stand, as indicated in the picture.
8. Insert the tubes which will later connect the front and the back frame. Attach
them with screws, using the pre-drilled holes. The front frame is now prepared
and can be placed on the security mat!
9. Insert the remaining frame feet to the back frame just like you did with the
front one.
10. Attach the two seat brackets to the back frame, but don't tighten the screws
yet.
11. Check the correct position of the brackets, by loosely placing the seat with
its rails extended on top and confirming that the drilled holes align with the holes
in the rails. Once confirmed, tighten the screws of the brackets.
12. Attach the seat to the back frame by using four screws and nuts. The easiest
way is to slide the seat forward by pulling up on the handle underneath. Screw
the seat to the brackets on the front end first. After this has been done, slide the
seat to the front (again use the handle for this) to expose the holes on the back
of the rails. Now attach the back to the brackets.
13. Attach the back frame with the seat to the front frame by placing the
connecting tubes into the open tubes of the back frame. Check the preferred
distance for the seat and use the remaining knurled screws to fix it, by screwing
them into the upward facing holes off the back frame. Don't forget that you can
adjust the distance later more easily by using the lever on the seat.
14. The seat is folded for shipping and easy storage. To lock the back into place,
RC-500
All manuals and user guides at all-guides.com
fold it upright, open the flap at the rear of the seat and lock the 2 securing bolts
into place on the left and right edges.
SECURITY MAT
We highly recommend to only use the RC-500 when placed on the included
security mat. The mat provides a secure stand for the seat and protects your
floor surface.
ADJUSTING THE DISTANCE BETWEEN WHEEL/PEDALS AND SEAT
Use the handle underneath the seat to easily slide the seat forward backward.
If you further need to adjust the distance, you can also re-adjust the position of
the front and back of the RC-500 by using the knurled screws at the bottom of
the seat.
NOTICE: To avoid injury, please pay attention when operating the handle and
sliding the seat into a new position.
MOUNTING OF RACING WHEELS
The wheel support has been prepared with holes which fit the majority of
racing wheels in the market. The screws are included with your RC-500.Simply
attach the screws through the wheel support plate and into the holes set in the
underside of your wheel.
NOTICE: The maximum height is marked by two lines on the tubes. To ensure a
stable wheel support, do not extend the frame beyond these points.
STORAGE
When you're not using the RC-500, you can disassemble it easily, by unscrewing
the two knurled screws at the bottom of the seat and separating the front from
the back frame. Furthermore you can fold the seat, for easier storage. Simply
open and lift the attached cover on the back and pull out the metal rods which
hold back and seat together.
WEIGHT NOTICE
Please note that this seat is only suitable to be used by persons with less than
110kg body weight.
IMPORTANT SAFEGUARDS & PRECAUTIONS
1. This product is for indoor use only. Never expose to wet weather
conditions.
2. Do not expose the unit to splashing, dripping, rain or moisture. Do not
immerse in liquid.
3. Do not expose to dust, high humidity, high temperatures or mechanical
shock.
4. Do not use if the equipment is damaged.
5. For external cleaning, use a soft, clean, damp cloth only.
6. This device is not designed to be used by anyone (including children)
with impaired physical, sensory or mental capacity, or by anyone without
appropriate experience or knowledge unless they have received prior
guidance or instructions related to the use of this device from someone who
is responsible for their safety. Children should be supervised to ensure that
they do not play with the device.
7. Take care of your extremities while operating the sliding handle of the chair.

CUSTOMER SUPPORT

For UK support contact: support@nacongaming.com