Product Safety - Wesco WS8512 Manual Del Usuario

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

PRODUCT SAFETY

WARNING: Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or serious
injury.
Save all warnings and instructions for future reference.
The appliance is only to be used with the power supply unit
provided with the appliance.
IMPORTANT
READ CAREFULLY BEFORE USE.
KEEP FOR FUTURE REFERENCE.
Safe operating practices
1) Training
a) Read the instructions carefully. Be familiar with the
controls and the correct use of the machine.
b) Never allow children, persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge or people unfamiliar with these
instructions to use the machine, local regulations may
restrict the age of the operator.
c) Never operate the machine while people, especially
children, or pets are nearby.
d) Keep in mind, that the operator or user is responsible
for accidents or hazards occurring to other people or
their property.
2) Preparation
a) While operating the machine, always wear substantial
footwear and long trousers. Do not operate the
machine when barefoot or wearing open sandals.
Avoid wearing clothing that is loose fitting or that has
hanging cords or ties.
b) Do not wear loose clothing or jewellery that can be
drawn into the air inlet. Keep long hair away from the
air inlets.
c) Obtain ear protection and safety glasses. Wear them at
all times while operating the machine.
d) Operate the machine in a recommended position and
only on a firm, level surface.
e) Do not operate the machine on a paved or gravel
surface where ejected material could cause injury.
f)
Before using, always visually inspect to see, that the
fasteners are secure, the housing is undamaged and
that guards and screens are in place. Replace worn
or damaged components in sets to preserve balance.
Replace damaged or unreadable labels.
EN
3) Operation
a) Before starting the machine, make certain that the
feeding chamber is empty.
b)
Keep your face and body away from the feed intake
opening.
c)
Do not allow hands or any other part of the body or
clothing inside the feeding chamber, discharge chute,
or near any moving part.
d) Keep proper balance and footing at all times. Do not
overreach. Never stand at a higher level than the base
of the machine when feeding material into it.
e)
Always stand clear of the discharge zone when
operating this machine.
f)
If the machine should start making any unusual noise
or vibration, immediately shut off the power source and
allow the machine to stop. Remove the battery pack
from the machine and take the following steps before
restarting and operating the machine:
i) inspect for damage;
ii) replace or repair any damaged parts;
iii) check for and tighten any loose parts.
g) Do not allow processed material to build up in the
discharge zone; this may prevent proper discharge and
can result in kickback of material through the intake
opening.
h)
If the machine becomes clogged, shut-off the power
source and remove the battery pack from the machine
before cleaning debris.
i)
Never operate the machine with defective guards or
shields, or without safety devices.
j)
Keep the power source clean of debris and other
accumulations to prevent damage to the power source
or possible fire.
k)
Do not transport this machine while the power source
is running.
l)
Always disconnect the machine from the power supply
(e.g. remove the battery pack from the machine)
- whenever you leave the machine,
- before clearing blockages or unclogging chute,
- before checking, cleaning or working on the machine.
m) Avoid using the machine in bad weather conditions
especially when there is a risk of lightning.
4) Maintenance and storage
a) Keep all nuts, bolts and screws tight to be sure the
appliance is in safe working condition.
b)
Replace worn or damaged parts.
c)
Use only genuine replacement parts and accessories.
d) Store the machine in a dry place out of the reach of
children.
e)
When the machine is stopped for servicing, inspection,
or storage, or to change an accessory, shut off the
7

Publicidad

Tabla de contenido

Solución de problemas

loading

Tabla de contenido