SATA ST96533 Instrucciones De Uso

ST96533, ST96535
ELECTRONIC TORQUE WRENCH WITH ANGLE OPERATING INSTRUCTIONS
LCD Display and Button Functions
Audible Select Unit of
Alert Measurement
• Color LCD • On/Off
Screen • Clear
• Exit Current
Setting
1. Power On
1. Verify torque is not being applied to the wrench. Press
Wrench will beep once.
2. The wrench will default to Peak Torque Mode. The last unit of measurement
and last torque setting will display.
3. The wrench is ready to use.
2. Power Off
1. If no torque is applied, wrench will shut off automatically after 90 seconds.
2. To shut off manually, verify torque is not being applied then press
3 seconds.
3. How to Change Unit of Torque Measurement
1. Power on the wrench as described in Section 1.
2. Press repeatedly to select one of the five torque measurement options:
· Kg-m
· Nm
· Ft-lb
· In-lb
· Kg-cm
3. The wrench is ready to use.
4. How to Set Mode
1. There are four mode options:
• P = Peak Torque (default)
• A = Angle
• PA = Peak Angle
• PCt = Target Torque Alert Setting
2. Power on the wrench as described in Section 1.
3. Press repeatedly to scroll through the different modes. "SEL" will
show at the top of the screen to indicate the mode being selected. The
currently selected mode will NOT show as an option when scrolling through
modes.
4. Press to select the new mode. The screen will show the last setting
for the mode selected.
Note: To exit out of setting mode without changing the mode, press
current mode and setting will remain unchanged.
5. How to Set Target Torque in "Peak Torque" Mode
1. Power on the wrench as
described in Section 1.
2. Press . The current torque
setting will flash on the screen.
3. The unit of torque measurement can also be adjusted at this time. Press
to change it if required.
4. Press or to select torque value, then press
5. The wrench is ready to use.
6. Apply torque and rotate the wrench at a constant moderate speed until
alerted to stop by the handle vibration, beeps and LCD display. The LCD screen
alternates red/green when the "target torque alert" warning starts. When the
target torque is reached the LCD Screen shows solid red.
Note: After reaching the target torque the display will flash for 10 seconds,
then default to the last setting. The next measurement can be taken while the
screen is flashing by applying force again, or by pressing
last setting.
6. How to Set Angle
1. Power on the wrench as
described in Section 1.
2. Place the torque wrench on a
stable flat surface to calibrate.
3. Press until the "A" mode is reached, then press
4. The screen will show "OOOO" as the torque wrench calibrates, then will
display the last angle value set.
5. If desired angle is displayed, the wrench is ready to use.
6. If you want a different angle, press again to change the angle
degree. Press or to get to the required angle, then press
7. The wrench is ready to use.
8. Apply torque and rotate the wrench at a constant moderate speed until
alerted to stop by the handle vibration, beeps and LCD display.
9. To take the next measurement press or wait until the display stops
flashing.
Note: After reaching the target angle the display will flash for 10 seconds, then
default to the last setting.
For better accuracy the torque wrench should be rotated between
10 degree/sec – 180 degrees/sec.
7. How to Change "Target Torque
Alert" and "Target Angle Alert"
Percentages
1. Power on the wrench as
described in Section 1.
2. Press until the "PCt" mode is reached, then press
3. The current value will flash on the screen.
Value (+) Change Mode
4. Press or
target torque alert can start at a maximum of 50% to the target torque value
or a minimum of 1% to the target torque value. For example, if your target
torque is 100 ft-lbs and your target torque alert is set at 50%, the alert will
start when you reach 50 ft-lbs. Press
5. The screen will show "dEG" so the target angle alert can be adjusted.
6. Press to change the target angle alert setting. Press
to select when the target angle alert will start. The target angle alert can
start at a maximum of 50 degrees before the target angle or a minimum of 5
degrees before the target angle. Press
Value (-) • Change Torque
7. The wrench is ready to use.
or Angle Value
Setting
8. How to Use Pre-Set Torque Values
• Select Option
Displayed
1. Power on the wrench as
• Select Torque
described in Section 1.
or Angle Value
2. Press then
screen will show the setting number
at the top of the screen and the torque value will be flashing.
for 2 seconds.
3. Press or
4. The wrench is ready to use.
9. How to Change Pre-Set Torque Values
Pre-Set Torque Values can only be
selected in Peak or Peak Angle modes.
1. Power on the wrench as
described in Section 1.
for
2. Press then
of the screen and the torque value will be flashing.
3. Press or
for 3 seconds, after which the wrench will beep.
4. Now the pre-set number at the top of the screen will flash. Press
to select the desired torque setting, then press
saved into the Pre-Set options.
5. Press again to set the target torque as to the new Pre-set value.
10. How to Set Torque with Angle
1. Power on the wrench as
described in Section 1.
2. Place the torque wrench on a
stable flat surface to calibrate.
3. Press until the "PA" mode is reached, then press
4. The screen will show "OOOO" as
the wrench calibrates, then will
show last angle and torque value set.
5. If the desired angle and torque
values are displayed, the wrench is ready to use.
6. If you want a different torque
value or angle , press
7. To change the torque value
press or
. The
required value, then press
The screen will show "ANG". If the
target angle value previously displayed
is correct, press
The wrench is ready to use.
8. After setting the torque value, the screen will show "ANG". Press
or change the angle value. Press
value, then press
9. The wrench is ready to use.
10. Apply torque and rotate the wrench at a constant moderate speed until
.
alerted to stop by the handle vibration, beeps and LCD display.
Note: After reaching the target torque the wrench will start recording the
angle measurement. After reaching the target torque and target angle the
display will flash for 10 seconds, then default to the last setting. To take the
next measurement press
11. Low Battery
1. When the remaining battery capacity is at 30%, the battery icon on the dis-
to return to the
play will flash. The Electronic Torque Wrench will still function, but the battery
will need to be replaced soon.
2. When the remaining battery
capacity is at 10%, the battery icon
will show continuously. The Electronic
Torque Wrench will not function correctly. Immediately replace the battery.
12. Changing Batteries
.
1. Use AA (Alkaline) Batteries only.
2. Remove Batteries if the torque wrench is not used for an extended period
of time.
3. Unscrew end cap
. .
to select when the target torque alert will start. The
to save.
to save.
. The
to select the desired pre-set torque value, then press
. The screen will show the pre-set number at the top
to select the desired pre-set torque value, then press
. The new Pre-Set Value is
.
again.
to get to the
.
to exit.
or to get to the required angle
again.
or wait until the display stops flashing.
4. Insert 2 AA (Alkaline) Batteries 5. Replace End Cap
13. Maximum Capacity Exceeded
1. When the applied torque exceeds
the wrench full-scale capacity the
LCD screen will show red. The
display will show "ovEr".
2. Verify the calibration of the wrench if you know its capacity has been
exceeded.
How to Apply Torque
1. This Electronic Torque Wrench is designed so that when force is properly
applied to the handgrip, a continuous audible signal, the LCD screen display
and vibration in the handle will indicate that the Target Torque or Angle has
been attained. DO NOT pull beyond this point.
or
Caution: The audible signal, LCD screen display and vibration in the the handle
are indicators that the proper torque or angle have been attained. Over torqu-
ing beyond these signals could cause fastener failure.
2. To properly apply torque, attach socket securely on torque wrench square
drive and position socket on fastener so that tilting will not occur. Grasp the
center of hand grip and apply a slow steady increasing force perpendicular
(90 degrees) to the torque wrench body and perpendicular (90 degrees) to the
center line of the square drive, socket and fastener.
3. Turn the fastener down with a smooth and even force applied to the handle
of the torque wrench. As turning resistance increases, pull more slowly. To
. assure accuracy, the fastener must be in motion when the torque measure-
ment is made.
WARNING: Any change from the above procedure will result in a change of
torque being applied. This includes standard torque wrenches, flex-head
torque wrenches, universal joints, and universal sockets. DO NOT USE universal
joints or universal sockets due to the complexity of determining the associated
error. If you need angular access, use a flex-head torque wrench.
Extensions
When it is necessary to use an extension that changes the effective lever
length of the torque wrench, torque being applied will change.
or
Compute adjustments as follows:
TW - Torque set on Wrench
TE - Torque applied by the extension to the fastener
TW = (TE x L) / (L + E)
TE = (TW x (L + E)) / L
Notice: Socket extension bars that are axially in line with the square drive do
not cause error and need no adjustment.
Apply torque and rotate the wrench at a constant moderate speed until alerted
to stop by the continuous audible signal, the LCD Screen display and handle
vibration.
Certification
This torque wrench was calibrated prior to shipment from the factory within
tolerance limits of:
• Torque (unflexed): +/- 2% CW, +/- 3% CCW from 20% to 100% of capacity
• Angle: (+/- 1% of reading) + (+/- 1 degree @ angular velocity >10 degree/
sec <180 degree/sec) + (+/- 1 degree of test fixture)
Limited Warranty
to review
Until one year from the date of purchase, we will repair any defect in material
or workmanship free of charge. Improper use of these products, including but
not limited to the application of excessive force, will affect performance and
may result in injury. The warranty does not apply to wrenches which do not
function properly or within specified accuracy because of wear, improper or
unreasonable use, damage not resulting from defect or malfunction, or which
have been altered. Calibration is warranted for 90 days. This warranty gives you
specific legal rights, and you may also have other rights which vary from state
to state. For repair or calibration send wrench, postage prepaid, to:
Angle Repair
175 Angle Dr
Beckley, WV 25801
Questions, comments or for more warranty information call toll free:
1-304-253-5729
WARNING
• Never use the torque wrench with the power off. Always turn on the
torque wrench so the applied torque is measured.
• Do not press any key while torque is being applied.
• Do not use electronic torque wrench to loosen fasteners.
• Verify the calibration of the wrench if you know or suspect its
capacity has been exceeded.
• Periodic recalibration is required to maintain accuracy.
• Never apply more torque than the maximum wrench capacity or the
maximum fastener specifications.
• Do not immerse in fluids.
• Do not use on live electrical circuits.
• Electrical shock can cause injury. Rubber handle is NOT insulated.