Transport And Storage - Hilti DD 130 Manual De Instrucciones

1. Fit the hole-starting aid into the front end of the dia-
mond core bit.
7.2.2 Vacuum cleaner without power socket for elec-
tric tools
Switching on
1. Switch the vacuum cleaner on.
2. Press the on / off switch on the tool.
Switching off
1. Switch the tool off.
2. Allow the vacuum cleaner to run for a short time in
order to remove remaining dust before switching off.
7.3 Hand-held wet drilling
Switching on
1. Open the water valve in the side handle until the desired
water volume flows. The water flow volume can be
observed at the indicator on the hand grip.
2. Press the on / off switch
3. When starting a hole, hold the tool at a slight angle to
the work surface. This makes hole-starting easier.
4. Once the hole has been started, bring the tool into the
90° position and continue drilling.
Switching off
1. Switch the tool off.
2. Close the water valve on the side handle.
7.4 Hand-held wet drilling using the water collection
system
The crosshair marks at the front end of the water col-
lection system serve as an accurate positioning aid.
Switching on
1. Switch on the water extraction system (if used).
2. Open the water valve on the side handle slowly until
the desired water volume flows. Use the indicator on
the side handle to check the water flow rate.
3. Press the on / off switch.
4. Hold the tool at a slight angle to the work surface when
starting a hole. This makes hole-starting easier.
5. After starting the hole, bring the tool into the 90° posi-
tion and continue drilling.
Switching off
1. Switch the tool off.
-WARNING-
When drilling overhead, any water remaining in the
core bit must not be allowed to run down over the
tool.
2. Close the water valve on the side handle.
3. Switch off the vacuum cleaner (if used).
4. Remove the core if necessary.
7.5 Wet drilling using the drill stand
Switching on
1. Switch on the (wet) vacuum cleaner (if used).
2. Open the water valve at the side handle slowly until
the desired volume of water flows. The indicator at
10
Printed: 08.07.2013 | Doc-Nr: PUB / 5069521 / 000 / 01
All manuals and user guides at all-guides.com
3. Use the switch actuator to run the tool in sustained
4. Release the chain arrestor.
5. Bring the core bit into contact with the work surface
6. Apply only slight pressure to the core bit when begin-
7.Keep an eye on the overload indicator while drilling.
Switching off
1. Close the water regulation valve at the side handle.
2. Pull the core bit out of the hole.
3. Engage the chain arrestor.
4. Switch the tool off.
5. Switch off the vacuum cleaner (if used).
6. Remove the core if necessary.
7. Switch the tool off.
8. Ensure stability of the drill stand by lowering the tool
7.6 Procedure in the event of the core bit sticking
The slip clutch will be activated if the core bit sticks. The
power tool must then be switched off by the operator.
To release the core bit, proceed as follows:
Using an open-end wrench to release the core bit
1. Disconnect the supply cord plug from the power out-
2. Grip the core bit close to the connection end with a
3. Plug the supply cord back into the power outlet.
4. Continue the drilling operation.
Using the spider wheel to release the core bit (for use
with the drill stand)
1. Disconnect the supply cord plug from the power out-
2. Release the core bit by rotating it with the spider wheel.
3. Plug the supply cord back into the power outlet.
4. Continue the drilling operation.

7.7 Transport and storage

-NOTE-
– Store and transport the power tool in is toolbox when
possible.
– Open the water flow regulator before storing the pow-
er tool. Especially at temperatures below freezing, take
care to ensure that no water remains in the power tool.
the side handle can be used to check the water flow
rate.
operation mode.
by turning the hand wheel.
ning drilling and then increase pressure once the core
bit has become centred.
Pressure on the core bit must be reduced if the over-
load indicator lights.
-WARNING-
When drilling overhead, any water remaining in the
core bit must not be allowed to run down over the
tool.
and core bit to the baseplate.
let.
suitable open-end wrench and rotate the core bit to
release it.
let.