TRANSPORTATION AND STORAGE
■
Stop the machine, disconnect from mains and allow it to
cool before storing or transporting.
■
Clean all foreign material from the product. Store it in a
cool dry and well-ventilated place that is inaccessible
to children. Keep away from corrosive agents such
as garden chemicals and de-icing salts. Do not store
outdoors.
■
Cover the blade with the blade protector before storing
the unit, or during transportation.
■
For transportation, secure the machine against
movement or falling to prevent injury to persons or
damage to the machine.
MAINTENANCE
WARNING
Use only original manufacturer's replacement parts,
accessories and attachments. Failure to do so can
cause possible injury, poor performance and may void
your warranty.
WARNING
Servicing requires extreme care and knowledge
and should be performed only be a qualifi ed service
technician. For service we suggest you return the
product to your nearest authorised service center for
repair. When servicing, use only identical replacement
parts.
WARNING
The blades are sharp. To prevent personal injury,
exercise extreme caution when cleaning, lubricating and
fi tting or removing the blade protector.
■
Switch off and disconnect from the mains before
conducting any maintenance or cleaning work.
■
You may only make adjustments or repairs described
in this manual. For other repairs, contact the authorised
service agent.
■
After each use, clean the body and handles of the
product with a soft dry cloth.
■
After each use, clean the debris from the blades
with a stiff brush, and then carefully apply a rust
preventative lubricant before refitting the blade
protector. The manufacturer recommends you to use a
rust preventative and lubricant spray to apply an even
distribution and reduce the risk of personal injury from
contact with the blades. For information about suitable
spray product check with your local authorised service
centre.
■
You may wish to lubricate the blades lightly before use
if necessary using the above method.
■
Check all nuts, bolts and screws at frequent intervals
for proper tightness to ensure the product is in safe
working condition. Any part that is damaged should be
properly repaired or replaced by an authorised service
centre.
INTENDED USE
The product is only intended for use outdoors by a single
operator who is standing on fi rm solid ground. For safety
reasons the product must be adequately controlled by
using two handed operation.
The product is designed for home or domestic use. It
is intended to cut and trim hedges, shrubs and similar
vegetation. The product is designed to be extended to
a maximum length of 2.6 m. Do not exceed this working
length.
It should be used in dry, well illuminated conditions.
It is not intended to cut grass, trees or branches. It should
not be used for any other purpose than hedge trimming.
RESIDUAL RISKS
Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise in use and the
operator should pay special attention to avoid the following:
■
The blades cannot be guarded whilst cutting. Contact
with the blades can cause serious injury. Keep the
blade away from yourself and others. Cover it with the
blade protector whenever you are not cutting.
■
Injury caused by vibration. Always use the right tool for
the job, use designated handles and restrict working
time and exposure.
■
Exposure to noise can cause hearing injury. Wear ear
protection and limit exposure.
RISK REDUCTION
It has been reported that vibrations from hand-held tools
may contribute to a condition called Raynaud's Syndrome
in certain individuals. Symptoms may include tingling,
numbness and blanching of the fi ngers, usually apparent
upon exposure to cold. Hereditary factors, exposure to
cold and dampness, diet, smoking and work practices
are all thought to contribute to the development of these
symptoms. There are measures that can be taken by the
operator to possibly reduce the effects of vibration:
■
Keep your body warm in cold weather. When operating
the unit wear gloves to keep the hands and wrists
warm. It is reported that cold weather is a major factor
contributing to Raynaud's Syndrome.
■
After each period of operation, exercise to increase
blood circulation.
■
Take frequent work breaks. Limit the amount of
exposure per day.
If you experience any of the symptoms of this condition,
immediately discontinue use and see your doctor about
these symptoms.
Injuries may be caused, or aggravated, by prolonged
use of a tool. When using any tool for prolonged periods,
ensure you take regular breaks.
Autogoods "130"
WARNING
English |
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
3