Main Features; Configuration - Comelit 1467 Manual Del Usuario

Warning
• This Comelit product was designed for use in the creation of audio and video communication systems in residential, commercial or industrial settings
and in public buildings or buildings used by the public.
• All activities connected to the installation of Comelit products must be carried out by qualified technical personnel, with careful observation of the
indications provided in the manuals / instruction sheets supplied with those products.
• Cut off the power supply before carrying out any maintenance procedures.
• Use wires with a cross-section suited to the distances involved, observing the instructions provided in the system manual.
• We advise against running the system wires through the same duct as the power cables (230V or higher).
• To ensure Comelit products are used safely: carefully observe the indications provided in the manuals / instruction sheets and make sure the system
created using Comelit products has not been tampered with / damaged.
• Comelit products do not require maintenance aside from routine cleaning, which should be carried out in accordance with the indications provided in
the manuals / instruction sheets. Any repair work must be carried out: for the products themselves, exclusively by Comelit Group S.p.A., for systems,
by qualified technical personnel.
• Comelit Group S.p.A. does not assume any responsibility for: any usage other than the intended use; non-observance of the indications and warnings
contained in this manual / instruction sheet. Comelit Group S.p.A. nonetheless reserves the right to change the information provided in this manual /
instruction sheet at any time and without prior notice.
• The module cannot be considered as part of a fire detection system. Incoming pre-alarm, alarm, evacuation and fault notifications on
internal units and switchboards are additional information and do not replace fire alarm system alerts.
Art. 1467 is an interface capable of addressing the alerts
generated by a fire detection panel to the ViP system.
The alert generation logic is managed by the connected
panels. The alerts, depending on the programming
implemented, are forwarded and shown on the internal
units and/or the porter switchboard.
The alerts reproduced on the internal units and
switchboards are shown below:
• Pre-alarm
• Alarm
• Evacuate (General evacuation of the building)
• Fault (General control panel fault. Information only
available on the switchboard).
The alerts are shown on the ViP devices by means of a
pop-up message and an audible indication. The message
shown can be reset 10" after it is received; the audible
indication is stopped automatically after 100". The
message remains visible until the user performs a manual
reset.
Compatible devices:
Art. 6802W, 6842W, 6702W, 6722W, 6742W, 1952N
DESCRIPTION Fig. 1 (page 2)
1. ViP system Ethernet port (AUTO IP)
2. Dip-switch to perform the "Reboot with predetermined
network settings" and "Restore factory settings"
procedure.
3. Power supply input via 1441, 1441B.
4. CV1 and CV2 for setting port A2 (Fig. 2)
5. CV3 and CV4 for setting port A3 (Fig. 2)
6. A4 Ethernet port, NO POE, for connection of the fire
detection panel (default: "Static IP address" 10.0.0.200,
netmask 255.255.255.0).
7. A3 "POE" Ethernet port, can be set as NO POE
(default: "Static IP address" 10.0.0.200, netmask
255.255.255.0).
8. A2 "POE" Ethernet port, can be set as NO POE
(default: "Static IP address" 10.0.0.200, netmask
255.255.255.0).
9. A1 "POE" Ethernet port (default: "Static IP address"
10.0.0.200, netmask 255.255.255.0).

MAIN FEATURES

Compatible system
DIN rail mounting
DIN modules (no.)
Power supply voltage
Min./max. absorption
Operating temperature
Operating relative humidity
IP protection rating
6

CONFIGURATION

This operation requires a PC loaded with the ViP Manager
software, version 2.9.1 or later.
The ViP Manager software is available to download free of
charge from the website pro.comelitgroup.com
RESTORE DEFAULT NETWORK SETTINGS
This procedure is used to restart the product with the
default network parameters while keeping the remaining
settings unaltered.
√ DIP in default position (OFF)
1. Cut off the device power supply
2. Set DIP1 to ON
3. Restore the device power supply
4. Wait for approximately 20-40 sec., until the
LEDs flash slowly and alternately (1 sec. red
/ 1 sec. green)
5. Reset all the DIP-switches to OFF
» The green LED will flash for 5 sec.
» The device will start up with the default
» The next time the device is restarted, the
RESTORE FACTORY PARAMETERS
This procedure is used to restore the factory settings for
all parameters.
√ DIP in default position (OFF)
1. Cut off the device power supply
2. Set all the DIP-switches to ON
3. Restore the device power supply
4. Wait for approximately 20-40 sec., until the
LEDs flash rapidly and alternately (0.1 red /
0.1 green)
5. Reset all the DIP-switches to OFF
» The red LED will flash for 5 sec.
» The device will restore all parameters to
ViP
Yes
4
48 56 Vdc
÷
50 mA
+5 +40°C
÷
25 75%
÷
IP30
network settings applied
saved parameters will be restored
the factory settings and restart as normal
OFF
1 2
OFF
1 2
OFF
1 2
OFF
1 2
1 2
OFF
1 2