Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Communication Setup
This allows you to perform and/or change the
communication settings and select the type of
Internet connection from Cable or Wireless (built-in).
This setting is required to use BD-LIVE functions, and
software updates that connect to the Internet.
NOTE
• For manually performing the setting, the following
information of the connected router or modem is required.
Confirm the information prior to the setting.
− IP address, netmask, gateway, DNS address
Cable/Wireless Select
Go to "HOME" > "Settings" > "Communication
Setup" >
1
Select internet connection type.
Press a/b to select "Cable/Wireless select" , then
press d or ENTER.
2
Press a/b to select "Cable" or "Wireless" , then
press ENTER.
When using a LAN Cable
NOTE
• Make sure that the LAN cable is connected to this player
if a wired Internet connection is made (see page 22). This
setting cannot be performed when a LAN cable is not
connected.
Ethernet Quick Setup (Cable)
Go to "HOME" > "Settings" > "Communication
Setup" >
1
Press a/b to "Ethernet Quick Setup (Cable)" ,
then press ENTER. The IP address and other
network setting is automatically obtained.
2
Press a/b to select "Change" , then press
ENTER.
3
For testing network setting, press a/b to select
"Test" , then press ENTER.
• If the test has failed, an error message appears. Try
to "Ethernet Setup (Cable)" setting as below.
a/b to select "Complete" , then press ENTER.
Ethernet Setup (Cable)
Go to "HOME" > "Settings" > "Communication
Setup" >
1
Press a/b to select "Ethernet Setup (Cable)" ,
then press d or ENTER.
2
Press a/b to select "Change" , then press
ENTER.
• For initializing the current setting, select "Initialize" ,
then press ENTER.
3
Press a/b to select "Auto IP" or "Manual IP"
• If selecting "Auto IP": The IP address is automatically
obtained.
• If selecting "Manual IP": The IP address, netmask,
gateway, DNS 1 and DNS 2 are manually entered.
4
Press ENTER.
• If selecting "Auto IP" in the step 3, go to the step 8.
5
Enter your IP address, Netmask, Gateway, DNS
1, DNS 2.
• Regarding each of the setup values, confirm the
specifications of your broadband router.
6
Press a/b to select "Proxy" then press d or
ENTER.
7
For setting the Proxy, press a/b to select "Use"
or "Not Use" , then press ENTER.
• If selecting "Use": Access the Internet via proxy
server. Enter your Proxy Address and Proxy Port.
Select "Next" , then press ENTER.
• If selecting "Not Use": Disables the use of a proxy
server.
8
For testing the connection to the Internet, after
confirming the settings, press a/b to select
"Test" , then press ENTER.
• "Test" is available only when setting to obtain the IP
address automatically. "Test" cannot be selected if
the IP address has not been obtained automatically.
• As a result of the test, if the Internet connection fails,
enter the setup values manually.
select "Complete" , then press ENTER.
When using Wireless LAN
CAUTION
• When performing the wireless communication setup,
security information for the wireless router/access
point (WEP, WPA or WPA2 key) is required. Check your
wireless router/access point's information prior to setup.
NOTE
• Before this player can access the Internet wirelessly,
setup of a wireless router/access point is required.
Go to "HOME" > "Settings" > "Communication Setup" >
1
Press a/b to select "Ethernet Setup (Wireless)" ,
then press d or ENTER.
2
Press a/b to select "Change" , then press ENTER.
• For initializing the current setting, select "Initialize" ,
then press ENTER.
3
Press
The player scans all of the available access
points and displays the points with the "Other
Network" selection bar on the screen.
• When no available access points are retrieved, only
the "Other Network" selection bar is displayed on the
screen.
4
Press a/b to select desired access point or
"Other Network" , then press ENTER.
• For access points which are set to hide the SSID
using the wireless router, select "Other Network" to
set the access point.
• If selecting desired access point, go to step 7.
• If selecting "Other Network" , go to the next step.
5
Enter the access point name.
6
Select "Next" , then press ENTER.
47
Press a/b to
(Continued on the next page)
Publicidad
Tabla de contenido
Solución de problemas
