V-TAC VT-ST303 Guia De Inicio Rapido

INSTALLATION INSTRUCTION
LED SOLAR STREETLIGHT
TECHNICAL DATA:
Model VT-ST303
Solar Panel Wa�s DC 9V, 50W
Lumens 3000LM
Beam Angle 120⁰
LED Chip Type SMD 2835
CRI >80
Maximum mounting height 6-8 Meters
Operation Temperature -20 to +45°c
Ba�ery Type LiFePO4 6.4V Ba�ery
Charging Time 4-6 hrs Sunlight Charging
Working Time 8-10hrs
Maximum installation height 6-8 Meters
No. of LEDs 572 PCS
INTRODUCTION & WARRANTY
Thank you for selecting and buying V-TAC product. V-TAC will serve you the best. Please read these
instructions carefully before starting the installation and keep this manual handy for future reference.
If you have any another query, please contact our dealer or local vendor from whom you have
purchased the product. They are trained and ready to serve you at the best. The warranty is valid for
3 years from the date of purchase. The warranty does not apply to damage caused by incorrect
installation or abnormal wear and tear. The company gives no warranty against damage to any
surface due to incorrect removal and installation of the product. This product is warranted for manu
facturing defects only.
3
IP65
RATING
*
WARRANTY
WARNING!
1. Installation must be performed by a qualified electrician
2. Replace any cracked protective shield.
3. Keep away from the fire.
4. Don't immerse in the water
5. Luminaire cannot be installed in low-lying areas, so as not to soak.
PARTS INCLUDED
Solar Panel Solar Light
1.2m Wire
Expansion Screw 2*6
8
7
Moun�ng Arm
Protruding Pole
(For Wall/Pole Installa�on) (For Solar Panel)
REMOTE CONTROL
3 hours regular
6 hours regular
8 hours regular
Full bright mode
ENGLISH
LAMP POST INSTALLATION
This marking indicates that this
product should not be disposed
of with other household wastes.
Light Source
Internal six angle
screw fixation
Hole
Remote Control
INSTALLATION GUIDE:
• Before installing please remove all the parts to check if all are in good condition or not.
• Install the Protruding Pole on a wall or on a Lamp Pole with the Expansion Screws
• Fix the Solar Panel on the Bracket. Fix them on the Mounting Arm and tighten the screws.
• Place the Mounting Arm on the top pole part of the Protruding Pole
Solar Panel Bracket
• Fix the Luminaire on the front portion of the Protruding Pole
• Make sure that the connection Plug on the luminaire is carefully stretched out from the hole
beneath the Protruding Pole
• Now Connect the plugs and tighten the Waterproof Cap.
• The luminaire should be connected to the solar panel against the sun light. Please makes
sure the solar panel is adjusted in correct angle in order to receive sunlight.
1 Expansion Plate
• After installation test the light using the remote control.
(For Lamp Post Installa�on) • The remote control is designed with an operation distance of 8-10m
MAINTENANCE
• Clean the light with a dry, lint-free cloth.
Optically controlled mode
• Check the solar panel for dirt regularly. If dirt or is present remove it to guarantee flawless
function of the product.
• Especially during the winter, keep the product free from snow and ice.
Force to turn on the lights
• Confirm installation direction is correct (solar panel should be at top)
(Optical control is null)
• Confirm no objects blocking the solar panel to receive sunlight
Force to turn off the lights
(Optical control is null)
IN CASE OF ANY QUERY/ISSUE WITH THE PRODUCT, PLEASE REACH OUT TO US AT: SUPPORT@V-TAC.EU
FOR MORE PRODUCTS RANGE, INQUIRY PLEASE CONTACT OUR DISTRIBUTOR OR NEAREST DEALERS.
Semi-bright mode
ENGLISH
WALL MOUNT INSTALLATION
Solar Charging
Solar Charging
(The battery is in the lamp housing)
(The battery is in the lamp housing)
Mounting Arm
(For Solar Panel)
Light Source
Screw fixation
Internal six angle
screw fixation
Protruding Pole
Expansion Plate Hole (For Wall/Pole Installation)
Protruding Pole
(For Wall/Pole Installation)
Plug the male and female plugs
and tighten the waterproof cap
V-TAC EUROPE LTD. BULGARIA, PLOVDIV 4000, BUL.L.KARAVELOW 9B
Mounting Arm
(For Solar Panel)
Screw fixation