Technical Data - Ritos 7065110A Indicación Para El Montaje Y El Servicio

GB
LED floodlight with movement sensor
Operation and maintenance manual
Dear valued customer,
Thank you for purchasing our floodlight.
Before operating the floodlight, please read the following instructions for use carefully and keep
them in a safe place for future reference
Proper Use
The floodlight is spray-protected, IP44 and for use outdoors
The floodlight conforms with the appropriate European CE regulations.
General Safety Instructions
• Never look directly into the LED light source. The light emitted can contain the colour blue.
• must always be placed at least 1m away from the surface being illuminated – in particular, the
power cable must not be illuminated or come into contact with the metal housing – maintain the
specified minimum clearances.
• must always be given sufficient time to cool down – the floodlight housing can get extremely hot –
the power supply to the floodlight must always be disconnected and locked out before servicing,
e.g. for bulb replacement or cleaning.
• must only be used on flat, stable surfaces.
• use only with a sufficiently protected 230V~ installation.
• must not be used in rooms that represent an explosion hazard (e.g. cabinetmaker's workshop,
painting operation, or similar).
• must not be used in the immediate vicinity of flammable materials.
• must not be set up in the immediate vicinity of pools, fountains, ponds, or similar bodies of water.
must not be immersed in water or other liquids.
• must not be immersed in water or other liquids.
• must not be operated with wet hands; never look directly into the light source.
• must never be covered.
• must never be operated with an open housing, missing or damaged wiring compartment, or
missing or damaged lens.
• must never be sprayed or cleaned using a steam pressure cleaner since this can damage the
insulation and seals.
• must never be repaired by the user. Repairs must only be carried out by the manufacturer or an
authorized service representative.

Technical Data

• 7065110A: Illuminant: 10W LED Chip Luminous flux: approx. 700lm
• 7065120A: Illuminant: 20W LED Chip Luminous flux:
• Voltage: 230V~, 50Hz
• Protection class: IP44
• Range max: 10m
• Response time: 5 sec.– 10 min
• Colour temperature: 6500K
6
All manuals and user guides at all-guides.com
Acquisition angle: 120°
1600lm Acquisition angle: 120°
Installing
Installation may only be carried out by trained professionals according to the applicable installation
regulations. Contact a licensed electrician.
ATTENTION!! Before installation, the power supply must be disconnected and locked out.
• Loosen the screws on the side of the housing and remove the mounting brackets.
• Install the mounting brackets to a suitable surface – always follow the installation location requi-
rements listed under "General Safety Information".
• Reattach the floodlight housing to the mounting brackets but do not tighten the screws fully.
• Loosen the screws on the back of the junction box and remove the cover.
• Remove the cable guide screw connection and guide it over the connecting cable – the screw
connection thread must face in the direction of the cable end.
• Loosen the cable grip screws and remove the cable grip.
• Guide the screw connection seal over the cable as well, and then insert the cable into the junction
box. Ensure the seal is seated in the cable guide correctly – if the connecting cable is too thin,
the cable guide must be additionally sealed.
• Connect the wires according to Figure 2.
• Tighten the cable guide screw connection, install the cable grip, and tighten the screws.
• Install the junction box cover and tighten the screws.
Setting the Floodlight Direction
Loosen the screws on the sides of the mounting brackets, adjust the floodlight direction, and then
retighten all screws.
Setting up the motion detector
• Turn both dials fully counter-clockwise (T). The floodlight turns on for approx. 1 minute and then
turns off.
• Walk the entire acquisition area. Once you leave the area, the halogen floodlight is turned off after
a time delay; upon re-entering the acquisition area, it is turned back on.
• The motion detector light sensitivity and activation time can be individually adjusted using the
dials.
Cleaning
• Disconnect and lock out the power supply to the floodlight. Allow the floodlight to cool down
sufficiently!
• Clean with a dry or slightly moist, clean, lint-free cloth and a mild detergent if required. Do not
use cleaners that contain abrasives or solvents.
• Disconnect and lock out the power supply to the floodlight. Allow the floodlight to cool down
sufficiently!
• Clean with a dry or slightly moist, clean, lint-free cloth and a mild detergent if required. Do not
use cleaners that contain abrasives or solvents.
• If required, the illuminant can be cleaned with a lint-free cloth moistened with ethyl alcohol.
ATTENTION! After cleaning the illuminant with ethyl alcohol, it must be allowed to air dry for at
least 20 minutes.
GB
7