Installing The Refrigerator - GE 20 Manual Del Propietario E Instalación

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

INSTALLING THE REFRIGERATOR

REFRIGERATOR LOCATION
• Do not install the refrigerator where the temperature
will go below 60°F (16°C) because it will not run often
enough to maintain proper temperatures.
• Do not install the refrigerator where the temperature
will go above 100°F (37°C) because it will not perform
properly.
• Install it on a floor strong enough to support it fully
loaded.
CLEARANCES
Allow the following clearances for ease of installation,
proper air circulation and plumbing and electrical
connections.
Standard Depth
Models
Sides
1/8" (3 mm)
Top
1" (25 mm)
Back
1" (25 mm)
REMOVE TOP CAP
(on some models)
•IMPORTANT NOTE: This refrigerator is 34-1/2" deep.
Doors and passageways leading to the installation
location must be at least 36" wide in order to leave
the doors and handles attached to the refrigerator
while transporting it into the installation location. If
passageways are less than 36", the refrigerator doors
and handles can easily be scratched and damaged.
The top cap and doors can be removed to allow the
refrigerator to be safely moved indoors. Start with Step A.
•If it is not necessary to remove doors, skip Step A.
Leave tape and all packaging on doors until the
refrigerator is in the final location.
•SKID REMOVAL: Tilt refrigerator to each side to
remove skid.
•NOTE: Use a padded hand truck to move this
refrigerator. Place the refrigerator on the hand truck
with a side against the truck. We strongly recommend
that TWO PEOPLE move and complete this installation.
Locate and remove the two Phillips head screws on
A
the top of the refrigerator. Remove the two screws
on each side at the rear of the top cap. Lift off and
remove top cap.
Remove the fresh-food door(s). Refer to Steps 1 and 3
B
of "Reversing the Door Swing" section or Steps 1 and
2 of "Removing the Doors" section.
C
Remove the bottom freezer drawer or door. Refer to
"Removing Freezer Drawer" section or Step 2 of
"Reversing the Door Swing" section.
D
Move refrigerator to the installation location.
All manuals and user guides at all-guides.com
Installation Instructions
16
REMOVE TOP CAP (cont.)
REINSTALL DOORS, DRAWERS AND TOP CAP
Carefully lower the door(s) onto the center hinge(s).
E
Reinstall top hinge(s). NOTE: Ensure the door is properly
aligned to the case top to avoid readjustment of the door
during top cap reinstallation.
Place cap over the top of the refrigerator. Reinstall
F
the original screws in the top and back of the cap.
Reinstall the bottom freezer drawer or door. Refer to
G
"Replacing the Freezer Drawer" section or Step 8 of
"Reversing the Door Swing" section.
Double-door models
A
CONNECTING THE REFRIGERATOR
1
TO THE HOUSE WATER LINE
(icemaker models)
A cold water supply is required for automatic icemaker
operation. If there is not a cold water supply, you will need to
provide one. See Installing the Water Line section.
NOTES:
• Before making the connection to the refrigerator, be sure the
refrigerator power cord is not plugged into the wall outlet.
• If your refrigerator does not have a water filter, we
recommend installing one if your water supply has sand
or particles that could clog the screen of the refrigerator's
water valve. Install it in the water line near the refrigerator.
If using GE SmartConnect
need an additional tube (WX08X10002) to connect the filter.
Do not cut plastic tube to install filter.
(on some models)
A
Top
Hinge B
Top Hinge B
Single-door models
Refrigerator Tubing Kit, you will

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

2223Gdsc3kcybb

Tabla de contenido