Página 2
Limited 1 year Warranty Read Before Beginning Assembly Dorel warrants this product to be free from defects in material and • Work in a spacious area and near where the unit will be used, preferably on a workmanship and agrees to remedy any such defect. This warranty covers carpet, or use a piece of the cardboard packaging to protect your floor and one year from the date of original purchase from authorized retailers.
Página 3
WARNING - Loft bed : Twin • STRANGULATION HAZARD - Never attach or hang items to any part of the bunk bed that are not designed for use with the bed; for example, but not limited to, hooks, belts and jump ropes. •...
PARTS LIST Α FRONT LEFT POST BACK LEFT POST FRONT RIGHT POST BACK RIGHT POST HEADBOARD TOP CROSS 1 PC 1 PC 1 PC 1 PC 2 PCS HEADBOARD PANEL HEADBOARD CENTER CROSS BOTTOM PANEL HEADBOARD BOTTOM CROSS LEFT SHORT GUARDRAIL POST 2 PCS 2 PCS 2 PCS...
Página 6
PARTS LIST SIDE RAIL (WITH 4 HOLES) SIDE RAIL (WITH 1 HOLE) LONG BOTTOM GUARDRAIL SLAT LEFT LADDER END 1 PC 1 PC 1 PC 13 PCS 1 PC LADDER STEP RIGHT LADDER END 2 PCS 1 PC Each part has a unique part number. Please reference the appropriate part number when contacting customer service for replacement parts.
Each part has a unique part number. PART NUMBERS Please reference the appropriate part number when contacting customer DA4050429 PART service for replacement parts. LABELS (French Gray) Before throwing any packaging, please T1009870 verify all contents and make sure you have...
HARDWARE LIST Ø1/4” x 100mm Ø12mm x 15mm Ø1/4” x 35mm Ø1/4” x 13mm JOINT CONNECTOR BARREL NUT JOINT CONNECTOR JCN NUT 8 PCS 8 PCS 4 PCS 4PCS Ø10mm x 40mm Ø8mm x 30mm Ø1/4” x 60mm Ø4mm x 30mm ALLEN KEY FLAT HEAD SCREW WOOD DOWEL...
Hardware Pack DA4050429 (French Gray) HP#: TDA4050429-00 Please do not completely tighten all the hardware, until the entire assembly is complete, unless otherwise indicated in the step-by-step instructions. The screw(s), bolt(s) to be used at each step are shown in actual size in the lower right corner of the...
Página 10
Step 1 lnsert wood dowels ❼ into the ends of headboard top cross E, headboard center cross G and headboard bottom cross I. lnsert headboard panel F into the grooves of the headboard top cross E and headboard center cross G. lnsert bottom panel H into the grooves of the headboard center cross G and headboard bottom cross I.
Página 11
Step 2 lnsert wood dowels ❼ into the ends of headboard top cross E, headboard center cross G and headboard bottom cross I. lnsert headboard panel F into the grooves of the headboard top cross E and headboard center cross G. lnsert bottom panel H into the grooves of the headboard center cross G and headboard bottom cross I.
Página 12
Step 3 Insert barrel nuts ❷ into side rails P & Q as C & D using joint connectors ❶. shown. Attach side rails P & Q to the posts A & B & Insert wood dowels ❼ into long guardrails posts B &...
Página 13
Step 4 Insert wood dowels ❼ into short guardrails M & N. Attach the short guardrails M & N to guardrail ❿. posts J & L and secure with joint connectors M & N using flat head screw ❻. Attach the guardrail leg K to short guardrail K to side rail P using joint connector ❸, hex Attach guardrail posts J &...
Página 14
Step 5 head screw ❻. Attach slat S to side rails P & Q using flat Use screwdriver to tighten flat head screws. x 26...
Página 15
Step 6 ❼ into the end of the ladder steps U. To assemble the ladder, insert wood dowels Attach left ladder end T and right ladder end connectors ❾. V to ladder steps U with wood joint...
Página 16
Step 7 screws ⓬ as shown. Attach the ladder to the top side rail P with...
Helpful Hints CAUTION: This unit is intended for use only with the products and/or maximum weights indicated. Use with other products and/or products heavier than the maximum weights indicated may result in instability or cause possible injury. • Move your new furniture carefully, with two people lifting and carrying the unit to its new location.
Preguntas, inquietudes, partes que faltan? CONTACTE DA4050429 (Gris Francés) NUESTRO DEPARTAMENTO DE SERVICIO AL CLIENTE ANTES DE DEVOLVER EL PRODUCTO A LA TIENDA. Si le faltan piezas o las que se incluyen están dañadas, con mucho Litera Mezanina junior gusto le enviaremos sus piezas de reemplazo sin cargo extra.
ADVERTENCIA - Litera Mezanina : Individual • PELIGRO DE ESTRANGULAMIENTO - Nunca cuelgue o ate en la cama artículos que no estén diseñados para usarlos con la cama; por ejemplo, pero no limitado a esto, ganchos, cinturones y cuerdas de saltar. •...
T1009980 Paquete de componentes Travesaño inferior de barandilla pequeña T1009990 Travesaño superior de barandilla pequeña T1010000 DA4050429 (Gris Francés) # de paquete: TDA4050429-00 Travesaño superior de barandilla grande T1010010 Riel lateral (con 4 agujeros) T1010020 Nota: Por favor apriete completamente los pernos durante el...
Instrucciones Límites de peso: 165 Lb / 75 Kg Inserta ❼ en los extremos de E, G e I. Adjunte S a P & Q con ❻. Paso 1 Paso 5 Inserte F en las ranuras de E y G. Inserta ❽...
Des questions, des préoccupations ou des pièces DA4050429 (Gris Français) manquantes? CONTACTEZ NOTRE SERVICE À LA CLIENTÈLE AVANT DE RETOURNER LE PRODUIT AU DÉTAILLANT. Si des pièces sont manquantes ou endommagées, nous Lit mezzanine junior expédierons volontiers vos pièces de rechange gratuitement.
Página 23
AVERTISSEMENT - Lit mezzanine : Une Place • RISQUE D'ÉTRANGLEMENT - Ne jamais placer ou suspendre des articles sur aucune partie du lit superposé qui ne sont pas conçus pour être utilisés avec ce lit; par exemple, mais n'étant pas limité à, des crochets, des ceintures, et des cordes à sauter. •...
Traverse inférieure de tête de lit T1009950 Quincaillerie Pied gauche de petit garde-corps T1009960 Pied central de petit garde-corps T1009970 DA4050429 (Gris Français) # de paquet: TDA4050429-00 Pied droit de petit garde-corps T1009980 Traverse inférieure de petit garde-corps T1009990 Traverse supérieure de petit garde-corps...
Instructions Limite de Poids: 165 Lb / 75 Kg Attachez S à P & Q avec ❻. Insérez ❼ aux extrémités de E, G et I. Étape 5 Étape 1 Insérez F dans les rainures de E et G. Utilisez un tournevis pour serrer les vis à tête plate. Insérez H dans les rainures de G et I.