On/Off Switch - Worx WU022 Manual Del Usuario

much work as new battery packs.
Important charging notes:
1.For a new battery or a battery that has been
in storage for sometime, please recharge the
battery before use. If you want to store the
battery for a long time, please fully charge the
battery pack to ensure maximum battery life.
2.Longer life and better performance can be
obtained if the battery pack is charged when
the air temperature is between 65
F (18 -24 C). Do not charge the battery pack
o o
in air temperatures below + 40
or above 105 F (40.5 C).This is important as
o o
it can prevent serious damage to the battery
pack.
3.Never freeze your charger or immerse charger
in water or any other liquid.
4.When the battery pack fails to produce
sufficient power on jobs that were previously
done easily, please recharge you battery, do
not continue to use under this condition.You
may charge a partially used pack whenever you
desire with no adverse affect on the battery
pack.
5.When charging it is normal that the charger
and battery pack may become warm to touch.
6.If the battery pack does not charge properly:
a.Check current at power outlet by plugging in
another appliance.
b.Plug and unplug to check whether the
charger is ok.
c.Check whether the battery has been
damaged.
d.Move the charger and battery pack
to a location where the surrounding air
temperature is approximately 65
(18 -24 C).
o o
e.If the charging problem persists, take the
tool, battery pack and charger to an authorized
service center.
f.Under certain conditions, when the charger
is plugged into the power supply, the exposed
charging contacts inside the charger can be
shorted by foreign material. Foreign materials
of a conductive nature such as metallic
particles should be kept away from charger
cavities. Always unplug the charger from the
power supply when there is no battery pack in
the charger or before attempting to clean.
Worklight
13L-WU022-M-060905.indd 9
All manuals and user guides at all-guides.com
4. TO REMOVE OR INSTALL BATTERY
PACK
Locate latches on the side of the battery pack
and depress both sides to release battery pack
from your light. Remove the battery pack from
your light. After recharge insert the battery
pack into the light's battery port. A simple slip
and slight pressure will be sufficient (See B).
F and 75

5. ON/OFF SWITCH

o o
To start your light, depress the protective cover
F (+4.5 C),
o o over the switch at the position marked "
To turn off, depress the protective cover again.
6. MULTI-POSITION FUNCTION
This allows your light to be aimed / directed in
any position to free your hands for working.
All two sections can be rotated independently
for any combination of position (See C.1, C.2).
7. TO REPLACE THE BULB
burn your fingers. Turn off your light
and allow to cool for several minutes
to ensure the bulb, head cover and lens
become cool before you replace a bulb.
Remove the battery pack from the flashlight
following the above instruction. Unscrew
the flashlight head cover (2) anticlockwise.
Take out the bulb with its frame (See D.1).
Use a new bulb to replace the old one (See
D.2).Then locate the frame tabs (a) under the
housing location (b) by locating one tab before
the other. Check the bulb is seated in the
F - 75 F
o o center of the spring. Replace the head cover
(2) by rotating clockwise, ensure it is located
correctly and do not force it when fitting.
Note: Always uses the correct specification
bulb.
8. BULB STORAGE.
You can find or locate your replacement bulb
in the storage area. Located at the bottom of
the light (See E).
9. DISPOSAL OF AN EXHAUSTED
BATTERY PACK
Warning: The bulb, head cover and
lens become hot when used, it could
To preserve natural resources, please
recycle or dispose of the battery pack
" .
09
ENG
2006-9-13 10:50:38